Bosch HBC36D753W Kullanım Kılavuzu - Sayfa 24

Fırın Bosch HBC36D753W için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Bosch HBC36D753W 36 sayfaları.

Sayfayı Yazdır

Problem

The appliance cannot be started, the dis-

play shows

"Cleaning system"

"Continue operation with

"Clean"

"Clock" appears in the display

The appliance is not in operation. A cook-

ing time is shown in the display.

"Automatic switch-off" appears in the dis-

play

"Fill water tank" appears even though the

water tank is full

"Fill water tank" appears even though the

water tank is not yet empty, or "Fill water

tank" does not appear even though the

water tank is empty

The water tank empties for no discernible

reason. The evaporator dish is overflowing

Liquid in the evaporator dish has fully

evaporated, even though the water tank is

full.

"Empty tank/clean?" appears in the display The appliance has not been used for at

There is a "pop" noise during cooking

When you cook with steam, a lot of steam

is created

When cooking with steam, a lot of steam is

produced repeatedly

Steam escapes from the ventilation slots

during cooking

The appliance is not producing steam

properly

Error message "E011" appears in the dis-

play

An error message "E..." appears in the dis-

play

The appliance is not heating. "Demo" is

shown in the display

Replacing the cooking compartment bulb

Heat-resistant 230 V/25 W halogen bulbs with seals are

available from the after-sales service. Please specify the E

number and FD number of your appliance.

Risk of burns!

Allow the cooking compartment and cooking compartment light

to cool before changing the bulb.

Always use a dry cloth to remove a new halogen bulb from the

packaging, otherwise it will not last as long.

Possible cause

The cleaning aid has been cancelled

Power cut

The rotary selector was accidentally oper-

ated

The

button was not pressed after mak-

ing the setting

The Automatic switch-off is active.

The water tank has not been pushed in

properly

The detection system is not working

The water tank is dirty. The mobile water

level indicators are jammed

The water tank was not closed properly

The tank lid seal is dirty

The seal in the tank cover is defective

The water tank has not been pushed in

properly

The feed line is blocked

least two days and the water tank is full

Cold/warm effect with frozen food, caused

by the steam.

The appliance is being automatically cali-

brated

The appliance is unable to calibrate itself

automatically if cooking times are too

short

Limescale has formed in the appliance

A button was pressed for too long or is

jammed

Technical fault.

A button combination was actuated

Notes/remedy

Press the

ance twice (see section: Cleaning aid. Pro-

ceed as described under "Emptying the

evaporator dish and wiping out the appli-

ance")

Reset the clock

(see section: Time-setting options)

Press the

with the

Press any button.

Slide in the water tank until it engages

Call the after-sales service

Shake and clean the water tank. If the

parts cannot be released, obtain a new

water tank from the after-sales service

Close the lid until you feel it engage

Clean the seal

Obtain a new water tank from the after-

sales service

Slide in the water tank until it engages

Descale the appliance. Check whether the

water hardness range is set correctly

Empty and clean the water tank. Always

empty the water tank after cooking

This is normal

Restore the appliance to the factory set-

ting (see section: Basic settings). Then

start steaming at 100 °C for 20 minutes

This is normal

Start the descaling programme.

Press the

message Press all of the buttons individu-

ally and check whether they are clean

Press the

message. Reset the clock if required.

If the error message appears again, call

the after-sales service

Disconnect the power supply and recon-

nect after 10 seconds. Within 2 minutes,

press the

Switch off the fuse in the fuse box or unplug at the mains.

Turn the cover anti-clockwise to remove.

Remove the bulb and replace with a bulb of the same type.

Slide the new seals and the clamping ring onto the glass

cover in the right order.

button. Then rinse the appli-

button

button or delete the setting

button

button to delete the error

button for 4 seconds