Drayton Lifestyle LP112 Kurulum Talimatları - Sayfa 2

Zamanlayıcı Drayton Lifestyle LP112 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Drayton Lifestyle LP112 2 sayfaları. Single channel timeswitch, dual channel programmer

Sayfayı Yazdır
Drayton Lifestyle LP112 Kurulum Talimatları
THE LP241 24hr ELECTRONIC PROGRAMMER Cont...
THE LP522 5/2-DAY ELECTRONIC PROGRAMMER Cont...
Set the central heating
Set weekday hot water
I
I
Press the YES button, and the display will ask 'SET CH PROG?'.
When you press SET? after setting OFF3 for the central heating,
the display will ask 'SET HW MON to FRI PROG?'.
I
Press YES and you'll see ON1, the start of your first central heat-
I
ing period. Adjust it in 1-minute steps using the – and + but-
Press YES, then set your times in the same way. Remember, in
tons. If the – and + buttons are held down, the time changes in
this mode you can have different times to your central heating if
10-minute steps.
you wish.
Set weekend central heating
I
When you press SET? after OFF3 for the weekday hot water,
the display will ask 'SET CH SAT SUN PROG?'. Press YES to
I
confirm, and alter the times in the same way.
Press SET?, and you'll see OFF1, the end of your first central
heating period. Adjust this in the same way, press SET?, then
repeat the procedure for ON2, OFF2, ON3 and OFF3.
Set weekend hot water
I
When you press SET? after OFF3 for the weekend central
Set the hot water
heating, the display will ask 'SET HW SAT SUN PROG?'.
I
When you press SET? after setting OFF3 for the central heating,
Press YES, and follow the procedure.
I
the display will ask 'SET HW PROG?'.
When you press SET? after OFF3 for HW SAT SUN, the
programmer will go back to normal operation.
THE LP722 7-DAY ELECTRONIC PROGRAMMER
I
LP722 – a 7-day program allowing for different timings on each
Press YES, then set your times in the same way. Remember, in
day of the week, with central heating and hot water working
this mode you can have different times to your central heating if
independently for up to 3 heating periods each day.
you wish.
I
If the timings haven't been set for you, then your programmer
When you press SET? after setting OFF3 for the hot water, the
will still be on the factory-set standard program. This has central
programmer will return to normal operation.
heating and hot water operating together – with the option of
having different timings for each day of the week. But it's easy
THE LP522 5/2-DAY ELECTRONIC PROGRAMMER
to make changes, and have heating and water working
independently – just follow the instructions.
LP522 – a 5/2-day program allowing for different timings at
Want to leave a timing as it is? Press SET? and move on to the
the weekends, with central heating and hot water working
next one.
independently for up to 3 heating periods each day.
If you need to reset your timings to the standard program and
If the timings haven't been set for you, then your programmer
start again, press 'SET' and '+' together to go back to the
will still be on the factory-set standard program. This means
pre-set program.
that central heating and hot water will operate together, with
If you don't press anything for two minutes, the programmer
the same timings for weekdays and different ones for the
automatically goes back to normal operation.
weekend. But it's easy to make changes, and have heating
and water working independently – just follow the instructions.
The standard program
Want to leave a timing as it is? Press SET? and move on to
the next one.
Your system will come on for up to 3 heating periods every
If you need to reset your timings to the standard program
24hrs. ON1 starts the first period, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
and start again, press 'SET' and '+' together to go back to
means your system won't respond, but if you want to activate
the pre-set program.
that middle period, change any other timings – read on.
If you don't press anything for two minutes, the programmer
automatically goes back to normal operation.
SWITCHING
The standard program
ON 1 – start of first timed period
Your system will come on for up to 3 heating periods every
OFF 1 – end of first timed period
24hrs. ON1 starts the first period, OFF1 finishes it, and so on.
ON 2 – start of second timed period* 12.00pm 12.00pm 12.00pm 12.00pm
Notice that ON2 and OFF2 are set to the same time.* This
OFF 2 – end of second timed period* 12.00pm 12.00pm 12.00pm 12.00pm
means your system won't respond, but if you want to activate
that middle period, or change any other timings – read on.
ON 3 – start of third timed period
OFF 3 – final switch-off of the day
WEEKDAYS
WEEKENDS
SWITCHING
HW
CH
HW
CH
ON 1 – start of first timed period
6.30am
6.30am
7.00am
7.00am
Changing the timings
I
OFF 1 – end of first timed period
8.30am
8.30am
9.00am
9.00am
Press the SET? button and you'll see 'SET PROG?'.
ON 2 – start of second timed period* 12.00pm 12.00pm 12.00pm 12.00pm
OFF 2 – end of second timed period* 12.00pm 12.00pm 12.00pm 12.00pm
ON 3 – start of third timed period
4.30pm
4.30pm
4.00pm
4.00pm
OFF 3 – final switch-off of the day
10.30pm 10.30pm 11.00pm 11.00pm
Set all weekdays
Changing the timings
First you set the times that are going to be the same for each
I
weekday, then you can select each day individually and make
Press the SET? button and you'll see 'SET PROG?'.
any further adjustments. If you want each day to be quite differ-
ent, go straight to 'Set each day.'
I
Press the YES button, and the display will ask 'SET MON to FRI
PROG?'.
Set the weekday central heating
I
Press the YES button, and the display will ask 'SET CH MON to
FRI PROG?'.
I
Press YES and the display will ask 'SET CH MON to FRI
PROG?'.
I
Press YES and you'll see ON1, the start of your first central heat-
ing period. Adjust it in 1-minute steps using the – and + but-
tons. If the – and + buttons are held down, the time changes in
I
10-minute steps.
Press YES, and you'll see ON1, the start of your first central
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
I
Press SET?, and you'll see OFF1, the end of your first central
heating period. Adjust this in the same way, press SET?, then
repeat the procedure for ON2, OFF2, ON3 and OFF3.
I
Press SET?, and you'll see OFF1, the end of your first central
heating period. Adjust this in the same way, press SET?, then
repeat the procedure for ON2, OFF2, ON3 and OFF3.
THE LP722 7-DAY ELECTRONIC PROGRAMMER Cont...
I
When you press SET? after setting OFF3 for the weekday central
heating, the display will ask 'SET HW MON to FRI PROG?'.
I
Press YES, then set your hot water times in the same way.
Remember, in this mode you can have different times to your
central heating if you wish.
Set each day
If, after you've set OFF3 for your hot water, you want to fine-tune
one or more weekdays, press SET? until you find the first day
you want to adjust – then go through the procedure, altering any
time you wish. Press SET? to move on to the next day. When
you've finished, press SET? until you see 'SET SAT SUN
PROG?'.
If you don't want to alter any individual days, keep pressing
SET? until you see 'SET SAT SUN PROG?'.
Set weekend
I
Press YES, and alter the central heating and hot water times in
the same way.
I
When you press SET? after OFF3 for HW SAT SUN, the pro-
grammer will ask the question TEST? If you want to test your
program, see below, otherwise press SET? again. If you don't
want to test your program, press SET? again – and you'll be
asked the question SET H'DAY? If you want to set a holiday
switch off, see page 23, otherwise press SET? again.If you're not
going to program in a holiday switch-off, then press SET? again
and your programmer will go back to normal operation.
Test your program
I
This test facility allows you to run through your program to check
that the timings are exactly what you want.
I
Answer YES to TEST? and the display will show Monday and
a time just past midnight. Press YES again and hold it down –
and the display will start to run through the days of the week,
pausing for a few seconds when it reaches an ON or an OFF
time. At each pause, the appropriate lights and circuits will come
on.
I
Release the YES button, and the display will stop running
and give you longer to identify a timing.
WEEKDAYS
WEEKENDS
I
Press YES once more, and the display will start running again –
HW
CH
HW
CH
and will continue all through the week until you press SET?
6.30am
6.30am
7.00am
7.00am
I
Press SET? and your programmer will go back to normal
8.30am
8.30am
9.00am
9.00am
operation.
Remember - The display shows the strict time sequence, so
4.30pm
4.30pm
4.00pm
4.00pm
ON1 for HW could be followed by ON1 for CH, then OFF1 for
HW etc Using this feature you can program your system to
10.30pm 10.30pm 11.00pm 11.00pm
SET A HOLIDAY SWITCH-OFF
Applicable to all models.
Using this feature you can program your system to switch off
while you're on holiday, then switch back on again in time to
have the house warm for your return.
I
Press SET? three times and you'll see 'SET H'DAY?'
I
Press YES to SET H'DAY? and the display will show '00'.
I
Using + and -, set the number of days you want the system to
be off.
I
Press SET, the display will show 'H'DAY' and the programmer
will switch off the system. It will then return to normal operation
after the set number of days.
Remember - The programmer counts each pass through
midnight as a day. So if on a Saturday morning you don't want
the heating on again until Tuesday morning, set for 3 days.
SETTING THE CLOCK AND DATE
Applicable to all models.
SETTING THE CLOCK
The clock in your programmer has been set at the factory,
and automatically accounts for British Summer Time.
However, should you need to set the clock, read on.
I
Press the SET? button until you see SET CLOCK?.
Set the hour
I
Press YES once, and then the hour will start to flash. Use the
– and + buttons to set the hour, checking for AM and PM.
SETTING THE CLOCK Cont...
Set the minute
I
Press SET?, and the minutes will start to flash. Use the – and +
buttons to set the exact time.
I
Press SET?, and 'SET DATE?' appears in the display.
If you don't want to change the date press SET? to go back to
normal operation. If you do, go on to the next section.
SETTING THE DATE
The weekday is automatically calculated from the date, so if
the weekday is incorrect you'll need to reset the date.
I
Press the SET? button until you see SET DATE?.
Set the year
I
Press YES and the year will start to flash. Use the – and + but-
tons to adjust.
Set the month
I
Press SET? and the month will start to flash. Use the – and +
buttons to adjust.
Set the day
I
Press SET? and the day will start to flash. Use the – and + but-
tons to adjust.
Set the Day Light Saving
I
Press SET? and the current DLS status will start to flash for day
light saving (British Summer Time). Use the – and + buttons to
turn on or off.
I
Press SET? to go back to normal operation.
USERS NOTES
Technical Helpline: 0333 7000 622
Web: www.draytoncontrols.co.uk
WIRING THE PROGRAMMER Cont...
Connection Charts
Gravity HW, Pumped CH with Room Stats
LWC3 Junction Box
Pump
5
2
3
1
2
3
4
5
6
7
8
9
10
11
12
L
N
E
L
N
E
Room Thermostat
Mains Input
Programmer
230V a.c.
1
2
3
3 1 2 4 5
N
3
RTS 1&2
L
3A
Mains
Lifestyle LP722 LP522 LP241 LP112 SM2
RTS 4,6,9&10
L
N
1
3
Isolator
Function
E
N
L
L
N
E
Mid-Position Valve System
LWC3 Junction Box
Pump
*7
2
E
1
2
3
4
5
6
7
8
9
10
11
12
L
N
E
L
N
E
Room Thermostat
Cyl. Thermostat
Programmer
3 2 1 4 5
6 7 8
RTS 1&2
N
L
3
Drayton
C
1 2
RTS 4,6,9&10
N
3
L 1
HTS 3
Lifestyle LP722 LP522 LP241 LP112 SM2
Function
Function
E
N
L
Mains Input
Motorized Valves
230V a.c.
1
2
3
5
3A
Drayton
Mains
22mm 3 Port Mid Position Valve
Isolator
28mm 3 Port Mid Position Valve
*
Refer to Boiler Handbook
Function of
CH
for wiring details of Pump
Leads
On
N
E
L
Overrun boilers. Use boiler
manufactures instructions.
Spring-Return 2-Valve System
LWC3 Junction Box
Pump
*7
2
3
1
2
3
4
5
6
7
8
9
10
11
12
L
N
E
N
E
L
Room Thermostat
Cyl. Thermostat
Programmer
3 2 1 4 5
8 6
3
RTS 1&2
N
L
Drayton
C
1 2
Lifestyle LP722 LP522 LP241 LP112 SM2
RTS 4,6,9&10
N
L 1
3
HTS 3
Function
Function
E
N
L
Mains Input
Motorized Valves
230V 50HZ
1
2
3
6
2
3
Drayton
22mm 2 Port Valve
3A
Mains
28mm 2 Port Valve
Isolator
N
Function of
L
E
Leads
Motor
*
Refer to Boiler Handbook
L
N
E
DHW VALVE
for wiring details of Pump
Overrun boilers. Use boiler
The white wire (28mm Valves) becomes live when the valve closes, it is not
manufactures instructions.
used and is wired to 'spare' terminals for sale isolation.
Make the wiring connections, as above, for the appropriate system.
INSTALLERS/ENGINEERS NOTES
For surface wiring, snap out the cable entry strip on the bottom edge
of the wall-plate. Lifestyle units are double-insulated and need no earth
connection, but an earthing continuity (loop) terminal is provided for
convenience.
After wiring, plug in the unit and tighten the securing screws.
Check the mains input has a 3A fuse, and switch on the mains.
Then set the timings as shown in the User's Guide.
ALWAYS SWITCH OFF THE MAINS BEFORE REMOVING
THE LIFESTYLE TIMESWITCH/PROGRAMMER – AND
NEVER FIT IT TO A LIVE WALL-PLATE!
Technical Helpline: 0333 7000 622
Web: www.draytoncontrols.co.uk
Boiler
* 1
2
3
7
Perm.
Switch
N
E
L
L
2
1
7
4
NOT
USED
N
L
1
2
3
4
HW
CH
HW
CH
OFF
OFF
ON
ON
Boiler
* 1
2
3
7
Perm.
Switch
E
N
L
L
2
1
8
6
4
NOT
USED
N
L
1
2
3
4
HW
CH
HW
CH
OFF
ON
ON
OFF
8
7
2
3
Boiler
HW
Live &
N
E
Off
HW on
Boiler
* 1
2
3
7
Perm.
Switch
N
E
L
L
2
1
NOT
8
4
USED
1
2
3
4
N
L
HW
CH
HW
CH
OFF
OFF
ON
ON
7
1
9
5
2
3
7
1
10
L
N.C
C
N.O
N.C
N
E
C
N.O
Aux.SW
Motor
Aux.SW
CH VALVE