CARLO GAVAZZI PPB01 Manuel - Sayfa 2

Röleler CARLO GAVAZZI PPB01 için çevrimiçi göz atın veya pdf Manuel indirin. CARLO GAVAZZI PPB01 4 sayfaları. Monitoring relays
Ayrıca CARLO GAVAZZI PPB01 için: Kullanım Kılavuzu (8 sayfalar)

Sayfayı Yazdır

DPB01, PPB01

Supply Specifications

Power supply

Rated operational voltage

through terminals:

L1, L2, L3, N

(DPB01)

5, 6, 7, 11

(PPB01)

M23 - Delta Voltage:

M48 - Delta Voltage:

M48 - Star Voltage:

Rated operational power

DPB01CM23, PPB01CM23

DPB01CM48, PPB01CM48

Mode of Operation

Connected to the 3 phases

(and neutral) DPB01 and

PPB01 operate when all 3

phases are present at the

same

time,

the

phase

sequence is correct (not

DPB01...N and PPB...N) and

the phase-phase (or phase-

neutral) voltage levels are

within set limits.

If one or more phase-phase

phase-neutral

voltages

exceeds the upper set level

or drops below the lower set

Overvoltage cat. III

(IEC 60664, IEC 60038)

208 to 240 VAC ± 15%

45 to 65 Hz

380 to 480 VAC ± 15%

45 to 65 Hz

220 to 277 VAC ± 15%

45 to 65 Hz

13 VA @ 230 ∆VAC, 50 Hz

13 VA @ 400 ∆VAC, 50 Hz

Supplied by L1 and L2

level, the red LED starts

flashing 2 Hz and the output

relay releases after the set

time period. In any case if

phase-neutral measurement

selected

both

phase-

phase

and

phase-neutral

voltages are monitored. If the

phase sequence is wrong or

one phase is lost, the output

relay releases immediately.

Only 200 ms delay occurs.

The failure is indicated by the

red LED flashing 5 Hz during

the alarm condition.

General Specifications

Power ON delay

Reaction time

Incorrect phase sequence or

total phase loss

Voltage level

Alarm ON delay

Alarm OFF delay

Accuracy

Temperature drift

Delay ON alarm

Repeatability

Indication for

Power supply ON

Alarm ON

Output relay ON

Environment

Degree of protection

Pollution degree

Operating temperature

@ Max. voltage, 50 Hz

@ Max. voltage, 60 Hz

Storage temperature

Housing dimensions

DIN-rail version

Plug-in version

Weight

Screw terminals

Tightening torque

Approvals

CE Marking

EMC

Immunity

Emissions

Example 1

(mains network monitoring)

The relay monitors over and

under voltage, phase loss

and correct phase sequence.

In case of DPB01...N or

PPB01...N, the relay moni-

tors over and under voltage.

Specifications are subject to change without notice (09.05.05)

1 s ± 0.5 s or 6 s ± 0.5 s

< 200 ms

(input signal variation from

-20% to +20% or from

+20% to -20% of set value)

< 200 ms (delay < 0.1 s)

(15 min warm-up time)

± 1000 ppm/°C

± 10% on set value ± 50 ms

± 0.5% on full-scale

LED, green

LED, red (flashing 2 Hz

during delay time)

LED, yellow

IP 20

3 (DPB01), 2 (PPB01)

-20 to 60°C, R.H. < 95%

-20 to 50°C, R.H. < 95%

-30 to 80°C, R.H. < 95%

22.5 x 80 x 99.5 mm

36 x 80 x 94 mm

Approx. 120 g

Max. 0.5 Nm

according to IEC 60947

UL, CSA

Yes

Electromagnetic Compatibility

According to EN 61000-6-2

According to EN 50081-1

Example 2

(load monitoring)

The relay releases in case of

interruption of one or more

phases, when one or more

voltages drop below the low-

er set level or exceed the

upper set level.