Dreadbox TELEPATHY BUNDLE Manuel

Kayıt Ekipmanları Dreadbox TELEPATHY BUNDLE için çevrimiçi göz atın veya pdf Manuel indirin. Dreadbox TELEPATHY BUNDLE 2 sayfaları.

Sayfayı Yazdır

power

Please use only the power supply included in the box to

power the unit.

Plug the adapter and open the power switch of the case.

The Green/Red LEDs should light up to indicate that the

system is powered.

It is normal for the enclosure to heat up on the bottom side

after a while.

Power supply specifications:

15VDC, center positive 5.5mm x 2.1mm barrel, 1.6A

basic connections

In order to get the advertised 6 Voice multitimbral synth please

use the following standard and recommended connections.

CONNECT:

The MIDI adapter to the MIDI IN of the 1

Telepathy module.

All the MIDI OUT to the MIDI IN of each Telepathy module

with the stereo 3,5mm jacks.

The ODD numbered telepathy (1

, 3

and 5

INPUT of the Phychosis module.

The EVEN numbered telepathy (2

, 4

and 6

INPUT of the Phychosis module.

Set the Audio Out level of each Telepathy at 50%. If you set

it higher, you will cause the Psychosis to overdrive!

Send the Psychosis Left and Right outputs to a stereo input

of a mixer, or to your monitors directly.

If you do not have a STEREO destination, and can only use

the system in MONO do the following:

Send ONLY one of the Psychosis outputs to your monitor or

mixer, and make sure that the Psychosis Spread is set to

MONO and that no LFO is applied on it.

initial setup

Control mode

There are quite a few ways to use this bundle, from a simple

UNISON to a 6 voice polyphonic synth or even a 6 voice

multichannel–multitimbral synth.

All these are achieved by setting up the control mode on the

master voice and by activating/deactivating the CC and

Program Changes on each individual module.

We suggest lots of experimentation with these settings so

that you can get the most out of your system.

Tuning and Calibration

All the Telepathies modules used in the bundle are checked

and calibrated one by one, on the bundle system.

Depending on your environment, recalibration might be

needed. In that case check the Telepathy manual for more

info on how to calibrate each module.

Additionally, in order to tune their oscillators in respect to

each other follow these steps:

Set the Modules into a Unison mode.

Press the MENU button on the 1

Then press both MENU and VOICE buttons at the same

time to enter the Chain mode.

Again press MENU once (the white LED should be lit).

Finally press the VOICE button to exit. Now the 6 modules

are on a UNISON Play mode.

Turn the CC and Program change on all modules ON.

For all of each 6 modules do the following:

Enter the 4

MENU page (the white LED).

Set all sliders at 0% and then again at 100%.

Press the VOICE button.

) to the LEFT

If you do that on all 6 modules, then CC and program

changes will be activated. This allows us to control

) to the RIGHT

everything from the 1

also set the 1

Set the 1

module on HARD MASTER.

Press the MENU button.

Press both VOICE and MENU buttons.

Press and hold the MENU button. If the VOICE LED goes

high, then that means that you have the HARD MASTER

mode on. If it goes dark, then it's the SOFT MASTER. In the

second case press and hold the MENU again until the

VOICE goes high. Then press the VOICE button to exit.

Enter the tuning mode on all modules.

Press the VOICE button.

Press the VOICE and the MENU button at the same time.

Do that on all 6 modules.

Tune everything with respect the 1st module.

Turn the volume on modules 3,4,5,6 down so that only the

and 2

module are audible.

Press a key on your keyboard. Then use the 1

module to sync the two modules.

Turn the volume on the 2

module volume and follow the same procedure until all

modules are in sync.

Exit the tuning mode by pressing the VOICE button.

module.

module, but keep in mind we should

module in a HARD MASTER mode.

slider on the

module down and open the 3

polyphony and multitimbrality

Telepathies have the ability to link to each other in order to

achieve polyphony and multitimbrality. Depending on the

internal settings—that will be explored further below—you

can achieve several combinations of behavior between the

modules, once you chain them.

Chain mode

To enter Chain Mode follow the steps below:

Press the Menu Button once.

While on the Menu Pages press both Menu & Voice Buttons

once to enter the Chain Mode.

Chain Mode is indicated by an alternating flashing of the

button LEDs.

To select the preferable amount of Voices (number of

Telepathy modules in the Chain), press as many times the

Menu Button of the first module. While pressing the button

the alternate flashing appears to the module that is being

linked. You can set up to 8 Voices in total.

On the Master Telepathy (First module) the four coloured

LEDs indicate the number of Voices linked (Linked modules).

Linked Voices 1-4 appear through the LEDs from bottom

up. Linked Voices from 5-8 appear the same way while

LEDs are flashing.