Anchor LIB-BP4 Kullanıcı El Kitabı - Sayfa 3

Konuşmacılar Anchor LIB-BP4 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Anchor LIB-BP4 4 sayfaları. Anchor lib-6000hcu2

Sayfayı Yazdır

DIVERSITY WIRELESS BY ANCHOR AUDIO

Anchor Audio UHF wireless is a 16 channel, diversity wireless system that receives signals with two independent antennae.

With diversity wireless the receiver processes the stronger signal, effectively minimizing dropouts and interference from other

transmitting sources. The antennae are mounted internally so there are no obstructions or risk of damage.

CHANNEL SELECTION - BUILT-IN RECEIVER

Before you can use your UHF wireless system, you will need to select a wireless frequency, set the built-in receiver, and micro-

phone transmitter, to that channel.

1. Choose from any of the 16 available wireless channels

2. Set the wireless channel selector knob "CHANNEL" to the channel/frequency you have chosen

If you have two wireless receivers repeat above for the second receiver. Remember each receiver/transmitter pair must be set

to different channels for proper operation.

NOTE: Ongoing wireless interference? The frequency you selected may be in use by

other systems in the area! Change channels until you find a clear frequency!

UHF WIRELESS CONTROLS

CD PLAYER LCD DISPLAY

OPERATING THE BUILT-IN CD PLAYER

Your built-in CD player features 'direct-in' play, power loading, anti-shock/skip CD mechanism, repeat & random play, three beam

laser tracking system and dual one bit D/A converters. By feeding the CD audio signal directly into the mixing bus the Liberty Sound

System is able to create a crisp, clear composite output of all your system inputs.

CD PLAYER BASIC OPERATION

Insert a disc into the player by gently sliding it, label side up, into the CD slot. The player will automatically load and begin playback

from the beginning of the disc. CD player controls are explained in detail below:

PLAY/PAUSE Press to play a loaded CD. Press during play-

back to pause, press again to resume.

Press once to advance CD to next track. Press

and hold to fast forward on the current track.

DOWN

Press once to go to previous track. Press and

hold to fast backward on current track.

EJECT

Press to unload a disc from the player. If CD

is not removed within 10 seconds it will be

automatically reloaded into the player.

CAUTION: To avoid noise at shut off, turn CD player off before you turn off the Liberty!

CD SLOT

CD POWER ON/OFF

TOP TRACK Press once to start playing the disc from the

first track.

RANDOM

Press for continuous, random track play-back.

Press again to resume normal play.

REPEAT

Press for continuous playback of the same

track. Press again to resume normal play.

POWER

Press to turn the CD player on/off. The sound

system will need to be turned off separately.

FEEDBACK

Feedback, a howling noise or shrill sound, is self-generated by the sound system. It's caused by a microphone picking up the sound

coming from the speaker and then re-amplifieing it. Once a feedback loop starts it continues until the system is adjusted.

FEEDBACK CAUSES

• Microphone too close, pointing towards

or in front of speaker

• Volume setting is too loud for room

• Sound reflecting off hard surfaces

AVOIDING & ELIMINATING FEEDBACK

• Point microphone in a different direction

• Keep microphone away from the speaker

• Place speaker in FRONT of the microphone

• Reduce the sound system volume levels

CONNECTING TWO OR MORE LIBERTY SOUND SYSTEMS

USING A LIBERTY UNPOWERED COMPANION SPEAKER (LIB-6001)

Connect one end of a speaker cable (SC-50) to the SPEAKER OUTPUT jack on the back of a powered Liberty sound system.

Connect the other end to the jack labeled IN on the back of a Liberty unpowered companion speaker.

NOTE: AC power is not required for an unpowered companion speaker.

USING POWERED LIBERTY SOUND SYSTEMS

This method uses the line-output feature of your Liberty sound system. Connect a speaker cable (EX-50PP) from the LINE OUT

jack on the first powered Liberty to the LINE IN jack on the second powered Liberty. Set the volume of the second Liberty to

maximum so that full volume control will be at the first or primary sound system.

FIRST POWERED

LIBERTY

NOTE: The line-output feature can also be used to send the signal to a sound

system in a different room or a separate recording device.

SPEAKER STAND SETUP

1. Loosen the Lower Collar Knob

LOWER

2. Separate the stand legs until

COLLAR

KNOB

the leg support Cross Braces

are parallel to the floor

3. Tighten the Lower Collar Knob

CROSS BRACES

CORRECT SYSTEM PLACEMENT

WRONG SYSTEM PLACEMENT

CAUTION: Feedback can damage your equipment

& may be hazardous to hearing.

SECOND POWERED

LIBERTY

EX-50PP CABLE

UPPER

COLLAR

4. Loosen the Upper Collar Knob and

KNOB

extend the center pole

5. Adjust height and retighten the

Upper Collar Knob

6. Place your Anchor sound system

on the stand