Bosch 1775E Kullanım/Güvenlik Talimatları Kılavuzu - Sayfa 3
Elektrikli Alet Bosch 1775E için çevrimiçi göz atın veya pdf Kullanım/Güvenlik Talimatları Kılavuzu indirin. Bosch 1775E 37 sayfaları. Tuckpointing grinder
Ayrıca Bosch 1775E için: Broşür (34 sayfalar), Kullanım/Güvenlik Talimatları Kılavuzu (33 sayfalar), Parça Listesi (2 sayfalar)
Sayfayı Yazdır
BM 3609929818 01-11:BM 3609929818 01-11 1/18/12 12:34 PM Page 3
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of
parts and any other condition that may
affect the power tool's operation. If damaged,
have the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
Safety Warnings Common for Grinding,
Sanding, Wire Brushing, and Abrasive
Cutting-Off Operations:
a) This power tool is intended primarily for
tuckpointing applications and some
small abrasive masonry cut off
applications. Read all safety warnings,
instructions,
specifications provided with this power
tool. Failure to follow all instructions listed
below may result in electric shock, fire
and/or serious injury.
b) This power tool is not recommended for
metal or wood cutting. Operations for
which the power tool was not designed may
create a hazard and cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because
the accessory can be attached to your
power tool, it does not assure safe
operation.
d) The rated speed of the abrasive wheels
must be at least equal to the maximum
speed marked on the power tool.
Accessories running faster than their
RATED SPEED can break and fly apart.
e) The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately guarded or controlled.
Power Tool-Specific Safety Warnings
illustrations
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool
bits etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
f) The arbor size of wheels, flanges,
backing pads or any other accessory
must properly fit the spindle of the
power tool. Accessories with arbor holes
that do not match the mounting hardware of
the power tool will run out of balance,
vibrate excessively and may cause loss of
control.
and
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess
wear, wire brush for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting
and installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and run
the power tool at maximum no-load
speed for one minute. Damaged
accessories will normally break apart during
this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The eye
protection must be capable of stopping flying
-3-
Service