Aleo S19 gen2 LK250 Hızlı Referans Kılavuzu - Sayfa 8

Solar panel Aleo S19 gen2 LK250 için çevrimiçi göz atın veya pdf Hızlı Referans Kılavuzu indirin. Aleo S19 gen2 LK250 20 sayfaları.

Sayfayı Yazdır

1. This Manual in Other Languages

8.4.2 Clearance under the modules

■

Minimum clearance

NOTE

• Rooftop or freefield mounting

Ensure a clearance of at least 4 cm between the rear

edge of the frame and the mounting surface (e.g. the

roof tiles) for the rear ventilation ofthe aleo module.

• Roof-integrated mounting

Ensure an appropriate interval, for example, to the

trough of the mounting system. Also ensure ade-

quate ridge ventilation, for example, with a roof

ridge ventilator.

■

Maximum clearance

NOTE

• The largest permissible clearance is defined by

national standards. This is used to design the instal

lation on the assumed effects of wind and suction.

• The actual maximum clearance of an installation is

determined by the sub-structure. Ensure that your

sub-structure adheres to the permissible clearances.

8.5

Avoiding seals

NOTE

• Avoid the use of a seal between aleo modules and

their mounting surface.

• Dry and cool operation can have a positive effect on

the performance as well as the service life of an

aleo module.

• Also for roof-integrated mounting, ensure good rear

ventilation to minimise loss of output which results

from a higher module temperature. Ensure adequa-

te ridge ventilation, for example, with a roof ridge

ventilator.

8.6

Clearance under the modules

NOTE

• Keep the space behind the laminate free of any

objects. This prevents damage to the insulating

back sheet and the junction box.

• Ensure that sharp or conductive parts (e.g. screws

or nails) do not protrude into the space behind the

module.

• If possible, take measures to prevent foreign ob-

jects (e.g. snow, ice, leaves, twigs, branches) from

being able to get behind the module.

Page 8/19

9 Electrical installation

9.1 Connectors

WARNING!

Incompatible or unsuitable connectors can

overheat. Fire hazard!

• Only use connectors that are the same type and

from the same manufacturer.

• Avoid using different types of connectors or ones

from different manufacturers, even :

- if connecting is possible

- if the connectors have the same basic designation

(e.g. "MC4") or

- if they are designated as "compatible".

_______________________________________________

You can find more details on this in the next two sections.

9.1.1 Module connectors

The various module types can be fitted with the following

connectors:

• Original Multicontact

• PV-JM601 (with locking)

You can find the specific connectors in the module data

sheet.

9.1.2 Connector peculiarities

NOTE

• Original Multicontact® MC4 connectors

• Only plug original Multicontact

connectors into original Multicontact

connectors.1

• PV-JM601 connectors

• Only plug PV-JM601 connectors into PV-JM601

connectors.

9.1.3 Replacing the connectors

You can remove the connector on a module and replace it

with another connector, if necessary. You retain the manu-

facturing warranty if you remove and mount with approved

tools in the proper way and according to the connector

manufacturer's instructions.

The original Multicontact® MC4 connectors are referred to as "MC4" in the data sheet.

aleo solar GmbH | Marius-Eriksen-Straße 1 | 17291 Prenzlau | Germany | [email protected]

MC4 (with locking)

MC4

Quick Reference Manual Rel. 4.2, 08/2015, en-GB-DE (1)

MC4