Bosch professional gsr 9,6-2 Orijinal Talimat Kılavuzu - Sayfa 7
Elektrikli Alet Bosch professional gsr 9,6-2 için çevrimiçi göz atın veya pdf Orijinal Talimat Kılavuzu indirin. Bosch professional gsr 9,6-2 39 sayfaları. Professional power screwdriver
Ayrıca Bosch professional gsr 9,6-2 için: Kullanım Talimatları Kılavuzu (30 sayfalar), Kullanım Talimatları Kılavuzu (28 sayfalar)
Sayfayı Yazdır
OBJ_BUCH-593-003.book Page 7 Thursday, July 21, 2011 3:06 PM
Cordless Drill/Driver
Max. torque for hard/soft screwdriving
application according to ISO 5393
Maximum drilling diameter (1st/2nd gear)
– Steel
– Wood
Max. screw dia.
Chuck clamping range
Drill spindle thread
Weight according to EPTA-Procedure
01/2003
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Assembly
Battery Charging
A battery that is new or has not been used for a longer period
does not develop its full capacity until after approx. 5 charg-
ing/discharging cycles.
To remove the battery 6 press the unlocking buttons 7 and
pull out the battery downwards. Do not exert any force.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.
Changing the Tool (see figure A)
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
turn the front sleeve 2 in rotation direction
The locking is released again to remove the tool when the
front sleeve 2 is turned in the opposite direction.
Replacing the Drill Chuck
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
Bosch Power Tools
GSR ...
7,2-2
Professional
Nm
21/9
mm
10/10
mm
17/12
mm
mm
1–10
3/8"
kg
1.4
Removing the Securing Screw (see figure B)
The keyless chuck 1 is secured with a securing screw 13
against unintentional loosening from the drill spindle. Com-
pletely open the keyless chuck 1 and unscrew the securing
screw 13 in rotation direction
curing screw has a left-hand thread.
Removing the Drill Chuck (see figure C)
Clamp the short end of an Allen key 14 into the keyless chuck
1.
Place the machine on a stable surface (e. g. a workbench).
Hold the machine firmly and loosen the keyless chuck 1 by
turning the Allen key 14 in rotation direction
tight-seated keyless chuck by giving the long end of the Allen
key 14 a light blow. Remove the Allen key from the keyless
chuck and completely unscrew the keyless chuck.
Mounting the Drill Chuck (see figure D)
The keyless chuck is mounted in reverse order.
Screw the securing screw 13 in anti-clockwise direction into
the opened keyless chuck. Always use a new securing screw,
as the threads are covered with a thread-locking compound
that loses its effect after multiple usage.
, until the tool can be in-
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
by hand.
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
9,6-2
12-2
25/10
27/11
10/10
12/12
20/13
23/14
6
6
7
1–10
1–10
3/8"
3/8"
1.5
1.6
. Please note that the se-
The drill chuck must be tightened with a tightening
torque of approx. 17–22 Nm.
1 619 929 J03 | (21.7.11)
English | 7
14,4-2
18-2
30/15
45/22
12/12
12/12
26/19
29/22
8
8
1–10
1–10
3/8"
3/8"
1.7
1.9
. Loosen a