Bosch 300 Series Kullanım Talimatları Kılavuzu - Sayfa 34

Kurutucu Bosch 300 Series için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Bosch 300 Series 50 sayfaları. Built-in wall ovens
Ayrıca Bosch 300 Series için: Kullanım Kılavuzu (40 sayfalar), Kullanıcı Kılavuzu (21 sayfalar), Kurulum Kılavuzu (6 sayfalar), Kurulum Kılavuzu (36 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kullanım ve Bakım Kılavuzu / Kurulum Talimatları (40 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (7 sayfalar), Kurulum Kılavuzu (28 sayfalar), Hızlı Başlangıç Kılavuzu (7 sayfalar), Kullanım ve Bakım Kılavuzu (32 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (7 sayfalar), Servis Kılavuzu (36 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (13 sayfalar)

Bosch 300 Series Kullanım Talimatları Kılavuzu
en-us Operating the Dishwasher
Terminating the wash cycle
(Reset)
Press and hold Start button P
1 .
T e r m i n a t i n g t h e w a s h c y c l e
for approximately 3 seconds until
the display reads ‹:‹‚.
Wait about 1 minute while the
2.
dishwasher drains.
Press On/Off button (.
3.
You may now power the dishwasher
back on and begin a new cycle if
desired.
Changing the wash cycle
When the Start button ( has been
pressed, the wash cycle cannot be
changed. The only way a wash cycle
can be changed is by terminating the
wash cycle (Reset).
InfoLight
®
While the wash cycle is running, a
light spot shines on the floor under
the appliance door.
Do not open the appliance door until
the light point is no longer visible on
the floor.
If the appliance door is not
completely closed, the light spot
flashes*.
If the appliance is installed at
eye-level, with flush furniture front, the
light point is not visible.
In darkened rooms, some light
scattering may be visible. This is
normal and cannot be changed.
You can switch the Infolight on or off.
Off
‚:‹‹
On
‚:‹‚
To change the setting:
Press the On/Off button (.
1.
Hold down function key # and
2.
press Start button P until the
display 8 indicates š:‹x (x can
be any number). Release both
buttons.
Press function key # until the
3.
display shows ‚:‹‚.
34
Press the function key 3 to
4.
switch the InfoLight
‚:‹‚ or off ‚:‹‹.
Press Start button P to save
5.
the setting.
Intensive drying
The final rinse uses a higher
temperature which improves the
drying result. The cycle time and
energy usage may be increased.
(Caution if utensils are delicate!)
This feature has two settings:
š:‹‹ Off
š:‹‚ On
Press the On/Off button (.
1.
Hold down function key # and
2.
press Start button P until the
display 8 indicates š:x (x can
be any number).
Release both buttons.
3.
Press function key # until the
4.
display 8 indicates the factory
set value š:‹‹.
Press function key 3 to switch
5.
the intensive drying feature on
š:‹‚ or off š:‹‹.
Press Start button P to save
6.
setting.
feature on
®