Andersen Windows & Doors 901724 Kurulum Kılavuzu - Sayfa 2

Böcek Kontrol Ekipmanları Andersen Windows & Doors 901724 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Andersen Windows & Doors 901724 14 sayfaları. 1-1/2” self-storing storm doors with balanced retractable insect screen and integrated close system

Sayfayı Yazdır

SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide.

WARNING

Follow manufacturers' instructions for hand and power

tools. Always wear safety glasses. Failure to do so could

result in injury, product or property damage.

CAUTION

Metal components of the entry and the storm door

may become hot when exposed to sunlight.

IMPORTANT

The insect screen is intended for reasonable insect

control and not the retention of objects, persons, or

pets within the interior. The insect screen material

will not stop a person from falling through the door.

RECOMMENDED TOOLS

Phillips

Drill

Screwdriver

Tape Measure

Safety Glasses

VERIFY MOUNTING SURFACE REQUIREMENTS AND MEASURE DOOR OPENING *

MEASURE -

Verify that the exterior brickmould, trim board or casing (exterior trim) is firmly attached to the opening

structure and is a material that is suitable to sufficiently fasten the storm door to the door opening. The

storm door will sag over time if the mounting surface is not sufficiently fastened to the entryway.

5/8"

To install the storm door, you must verify that the opening width, height and mounting surface

are suitable size to properly install into the opening.

Measure the width at the top (W1), middle (W2), and bottom (W3) of the opening

5/8"

Measure from the inside of the exterior trim. Utilizing the narrowest width, reference chart below.

Measure the height at the left and right of the opening, from the bottom of the exterior trim at the

top of opening down to the sill at the bottom of opening. Reference chart for height compliance.

Nominal Storm Door Widths

1 1/2"

36" x 80"

34" x 80"

1/2"

32" x 80"

30" x 80"

Make sure that the exterior trim meets the mounting surface requirements. The assembly needs

1 1/2"

a minimum of 3/4" flat surface on exterior trim face, 1" minimum depth of mounting surface

Figure

2). A minimum depth of 3 1/8 inches for storm door handle clearance.

•

3/4" minimum flat surface on exterior trim face

•

1" minimum depth of mounting surface

•

minimum depth of 3 1/8 inches for storm door handle clearance

If your opening does not fit within these dimensions, call the Solution Center at 1-800-933-3626,

as there may be a solution that will work for your opening. .

Nominal storm doors sizes are listed. The actual storm door frame width and height will be less.

Example: A nominal size of 36" x 80" may have an actual storm door frame size of 35 1/8" x 79 1/8".

Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough

strength to lift, carry, and install window and door products. Heavier windows and doors will require mechanical

assistance. Failure to do so could result in injury, product or property damage.

Metal fasteners and components could corrode when exposed to preservative-

treated or fire-retardent treated lumber. Use approved fasteners and components

to fasten window or door. Failure to do so could cause a failure resulting in injury,

product or property damage.

Fastener must attach to a structural framing member with a 1" minimum fastener

embedment. Failure to do so could result in injury, product or property damage.

DO NOT remove screws that attached installation clips or gusset plates to window

or door frames. Doing so could result in injury, product or property damage.

1/8 Drill Bit

Straight head

Screwdriver

Pliers

5/8"

1/2"

Opening Widths

35 7/8" – 36 3/8"

1/2"

33 7/8" – 34 3/8"

31 7/8" – 32 3/8"

29 7/8" – 30 3/8"

(see Figure 2)

WARNING

Signal Word and Consequence

COULD

Result in:

COULD

Result in:

Work Gloves

1/2"

(see Figure

1).

Opening Heights

1 1/2"

80" (80" – 80 7/8")

1 1/2"

(see

(see Figure

3).

(see Figure 3)

WARNING

Storm doors have small

parts. Small parts if

swallowed could pose a

choking hazard to young

children. Dispose of unused,

loose, or easily removed small

parts. Failure to do so could

result in injury.

This is the Safety Alert Symbol used to alert you to

potential injury hazards. Obey all safety messages that

follow this symbol to avoid possilbe injury or death.

WARNING

COULD

Result in:

Major Injury / Death

NOTICE

Product or Property

Damage

1/2"

Figure 1

WARNING

CAUTION

Minor Injury

IMPORTANT

Procedure and Product

Information

1/2"

3/4" MIN

FLAT SURFACE

1/2"

1" MIN DEPTH

Figure 2

3 1/8" MIN DEPTH

Figure 3