Bosch 11536VSR - 36V Cordless 1" SDS-plus Litheon Rotary Hammer K Kullanım/Güvenlik Talimatları Kılavuzu - Sayfa 14

Matkap Bosch 11536VSR - 36V Cordless 1" SDS-plus Litheon Rotary Hammer K için çevrimiçi göz atın veya pdf Kullanım/Güvenlik Talimatları Kılavuzu indirin. Bosch 11536VSR - 36V Cordless 1" SDS-plus Litheon Rotary Hammer K 45 sayfaları. Cordless hammer drill

Sayfayı Yazdır

BM 1619929800 12-07

1. The charger was designed to fast charge

the battery only when the battery temperature

is between 32˚F (0˚C) and 140˚F (60˚C). If the

battery pack is too hot or too cold, the charger

will not fast charge the battery. (This may

happen if the battery pack is hot from heavy

use). When the battery temperature returns to

between 32˚F (0˚C) and 140˚F (60˚C), the

charger will automatically begin charging.

2. A substantial drop in operating time per

charge may mean that the battery pack is

nearing the end of its life and should be

replaced.

3. Remember to unplug charger during storage

period.

4. If battery does not charge properly:

TOOL TIPS

Following a few simple tips will reduce wear

on the tool and the chance of injury to the

operator.

NOTE: The high efficiency available from the

rotary hammers can only be obtained if sharp

and undamaged accessories are used. The

"cost" to maintain sharp and undamaged

accessories is more than offset by the "time

saved" in operating the tool with sharp

accessories.

You will extend the life of your bits and do

neater work if you always put the bit in contact

with the workpiece BEFORE pulling the trigger.

During operation, hold the drill firmly and exert

moderate, steady pressure. Too much

pressure at low speed will stall the hammer.

Too little pressure will keep the bit from cutting

and cause excess friction by sliding over the

surface. This can be damaging to the drill and

bit.

Shanks of all drill bits should be wiped clean

prior to using and immediately after removing.

Recall these instructions for safe operation:

1. Some materials require slow drilling

speeds; whereas, others require higher speed

to produce the best results.

2. All work must be supported or secured

before drilling and steady, even pressure

applied in line with the drill bit.

3. As the drill bit cuts through the opposite

side, reduce the pressure and continue

running the drill as the bit is withdrawn.

12/4/07

8:32 AM

IMPORTANT CHARGING NOTES

-14-

Page 14

a. Check for voltage at outlet by plugging in

some other electrical device.

b. Check to see if outlet is connected to a

light switch which turns power "off" when lights

are turned off.

c. Check battery pack terminals for dirt.

Clean with cotton swab and alcohol if

necessary.

d. If you still do not get proper charging,

take or send tool, battery pack and charger to

your local Bosch Service Center. See "Tools,

Electric" in the Yellow Pages for names and

addresses.

Note: Use of chargers or battery packs not

sold by Bosch will void the warranty.

Materials such as glass, porcelain, ceramics,

tiles, plastics, etc., should be drilled at low

speeds with specially designed drill bits and

lubricants.

DRILLING WOOD OR PLASTIC

If backing block is not used, ease up on the

pressure just before the bit breaks through the

wood to avoid splintering. Complete the hole

from the opposite side immediately after the

point breaks through. If bit binds, reverse the

drilling operation to help remove the bit from

the work.

DRILLING METAL

Make a center punch in the material for easier

starting. Use enough pressure to keep the bit

cutting. If the bit is allowed to merely spin in the

hole, it will become dull within a short time.

When drilling a larger hole, it is faster and

easier on your power pack to first make a

smaller hole and enlarge it to the required size.

Lubricate the tip of the bit occasionally with

CUTTING OIL for easier metal drilling. If bit

binds, reverse the drilling to help remove the

bit from the work.

DRILLING MASONRY

Use carbide-tipped masonry bit for cinder

block, mortar, common brick, soft stone and

other materials. The amount of pressure to

be used is dependent upon the type of

material being drilled. Soft materials require

less pressure while the hard materials need

more pressure to prevent the drill bit from

spinning.