Electrolux E30WV60PPS Kurulum, Kullanım ve Bakım Kılavuzu - Sayfa 5

Havalandırma Davlumbazı Electrolux E30WV60PPS için çevrimiçi göz atın veya pdf Kurulum, Kullanım ve Bakım Kılavuzu indirin. Electrolux E30WV60PPS 12 sayfaları. 30"(76.2 cm) and 36"(91.4 cm) range hood
Ayrıca Electrolux E30WV60PPS için: Kurulum, Kullanım ve Bakım Kılavuzu (12 sayfalar)

Sayfayı Yazdır

List of Materials

CAUTION!
Remove carton carefully. Wear gloves to protect
against sharp edges.
Parts supplied with unit for the installation
•
Hood canopy assembly with blower.
•
Lamp already installed.
•
Transition (3
⁄
" x 10" rectangular)
1
4
•
Grease filter.
•
Hardware bag with:
•
Use and Care / Installation Manual
•
3- 4x8 screws (to assemble Transition)
•
6- 4,5x13 screws
•
4- 10x50 screws
•
Torx 20 Adapter
Remove the protective film covering the product be-
fore putting into operation.
Tools/Materials required
•
Wire nuts
•
Metal duct length to suit installation
•
⁄
" Romex wire connector
1
2
•
Measuring tape
•
Pliers
•
Gloves
•
Knife
•
Safety glasses
•
Electric drill with
⁄
" and
5
16
•
Spirit level
•
Duct tape
•
Screwdrivers:
•
Phillips (Posidrive) #2
•
Torx # 2
•
Wire cutter/stripper
•
Masking tape
•
Hammer
•
Saw, jigsaw or reciprocating saw
List of materials- Electrical & Installation
⁄
" Bits
3
8

Electrical Requirements

Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and
in conformance with National Electrical Code, ANSI/
NFPA 70 (latest edition), or CSA Standards C22.1-
94, Canadian Electrical Code, Part 1 and C22.2 No.
0-M91 (latest edition) and all local codes and ordi-
nances.
If codes permit and a separate ground wire is used, it
is recommended that a qualified electrician determine
that the ground path is adequate.
A copy of the above code standards can be obtained
from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
•
A 120 volt, 60 Hz., AC only, 15-amp, fused
electrical circuit is required.
•
If the house has aluminum wiring, follow the
procedure below:
1. Connect a section of solid copper wire to the
pigtail leads.
2. Connect the aluminum wiring to the added
section of copper wire using special co
nectors and/or tools designed and UL listed
for joining copper to aluminum.
Follow the electrical connector manufacturer's recom-
mended procedure. Aluminum/copper connection
must conform with local codes and industry accepted
wiring practices.
•
Wire sizes and connections must conform with
the rating of the appliance as specified on the
model/serial rating plate.
The model/serial plate is located behind the filter
on the top wall by the electrical box.
•
Wire sizes must conform to the requirements of
the National Electrical Code, ANSI/NFPA 70 (la
est edition), or CSA Standards C22. 1-94,
Canadian Electrical Code, Part 1 and C22.2
No. 0-M91 (latest edition) and all local codes and
ordinances.
requirements
5