Atlas STRATEGY AA35 Kullanıcı Kılavuzu - Sayfa 2

Amplifikatör Atlas STRATEGY AA35 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Atlas STRATEGY AA35 3 sayfaları. Strategy series
Ayrıca Atlas STRATEGY AA35 için: Broşür (2 sayfalar), Broşür ve Teknik Özellikler (10 sayfalar)

Sayfayı Yazdır

The mixer/amplifier shall control and mix up to three input signals

and deliver an audio output of 35W into 8 Ohm, 25V, and 70V.

The amplifier output shall be transformer isolated with a frequency

response 50Hz to 20kHz (-3dB) with less than 0.5% THD at rated

output. The output regulation shall be less than 2dB, no load to full

load. It shall be capable of operation from a 110/120 VAC 50/60Hz

line. The mixer/amplifier shall be convection cooled. The amplifier

shall have thermal and short circuit protection.

The mixer/amplifier shall have a switch- selectable MIC/TEL balanced

input to accept either low impedance microphone or Tel/Line Level

signals with -60/-10dBv sensitivity. The MIC/TEL input shall include a

Phoenix (Euro Block) type connector. The MIC/TEL input impedance

shall be 600 Ohms. The MIC/TEL input shall include an auto mute

(VOX Mute) sensitivity control for Input 1. The MUTE SENSE control

will allow threshold adjustment of mute activation. The mixer/amplifier

shall include two stereo summing auxiliary inputs, unbalanced,

-10dBv, with dual-RCA jacks. The Auxiliary input impedance shall

each be 10k Ohms. The mixer/amplifier shall include two Zone

2 outputs, a 1W at 8 Ohms output and transformer isolated 600

Ohm output with a maximum level of 1.5VRMS. The mixer/amplifier

Zone 2 output shall be assignable from any of the 3 inputs via the

rear panel dipswitch. The Zone 2 output shall have one rear panel

mounted rotary level control for both outputs. The mixer/amplifier

shall incorporate rear panel terminals via Phoenix connector for the

REMOTE MUTE function, controlled by an external switch closure. A

rear panel dipswitch shall allow assignment of Input 2 and/or Input 3

to respond to the mute function activation. The Mute assignment shall

not affect the Zone 2 output.

The mixer/amplifier shall have a Pre-Out RCA unbalanced output.

The Pre Out shall be POST Tone and the Low Cut Filter. The mixer/

amplifier shall have a Power Amp input for use with an external

signal processor. The mixer/amplifier shall have a Line A and B RCA

unbalanced output. The Line outputs are POST tone controls, Low

1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 / FAX (800) 765-3435

ARCHITECT AND ENGINEER SPECIFICATIONS

Specifications subject to change without notice

Printed in U.S.A.

Cut Filter and Power Amp In. Both the Line and Pre Outputs shall be

calibrated to 0dBv and equals 1 VRMS out. The mixer/amplifier shall

have a 400Hz 6dB per octave low cut filter. The filter can be defeated

via the dipswitch located on the rear panel. When engaged the Bass

Tone control is bypassed.

The AA35 front panel shall include Inputs 1, 2, and 3 volume controls.

System Signal, Peak and Power LEDs shall also be incorporated. The

mixer/amplifier front panel shall also include Bass and Treble tone

controls (100Hz and 10kHz, ±10dB). The tone controls shall not affect

the Zone 2 output. The mixer/amplifier front panel shall include an AC

Mains power switch.

A rear panel AC receptacle (un-switched) shall be included for

connection of external equipment.

Dimensions (W x H x D) shall be 8.27" x 3.66" x 10.87" (210mm x

276mm x 93mm) with feet or 3.48" (88.4mm) H without feet. Net

weight shall be 10.2lbs. (4.64kg). Front panel finish and material

shall be black ABS resin and case finish (and material) shall be black

powder coated sheet steel.

The mixer/amplifier shall be Atlas Sound Model AA35.

The optional rack-mount bracket kit shall be an Atlas Sound

AARMK2-5.

The optional input transformer shall be an Atlas Sound AAIT-600.

The optional level control security covers shall be an Atlas Sound

AAVCC-5.

AtlasSound.com

ATS002452 RevA 11/06

SL5-2090