Bosch Series 4 Kullanım Kılavuzu - Sayfa 7

Sayfayı Yazdır

Damage to the plinth drawer

Caution!

Do not place hot objects in the plinth drawer. It could be

damaged.

Set-up, gas and electricity connection

Gas connection

Installation must only be performed by an approved expert or a

licensed after-sales service engineer in accordance with the

instructions specified under "Gas connection and conversion to

a different gas type".

For the licensed expert or after-sales service

Caution!

The setting conditions for this appliance are specified on the

■

rating plate on the back of the appliance. The gas type set in

the factory is marked with an asterisk (*).

Before setting up the appliance, check the grid access

■

conditions (gas type and gas pressure) and ensure that the

gas setting of the appliance meets these conditions. If the

appliance settings have to be changed, follow the instructions

in the section "Gas connection and conversion to a different

gas type".

This appliance is not connected to a waste gas main. It must

■

be connected and commissioned in accordance with the

installation conditions. Do not connect the appliance to a

waste gas main. All ventilation regulations must be observed.

The gas connection must be made via a fixed, i.e. not mobile

■

connection (gas line) or via a safety hose.

If using the safety hose, ensure that the hose is not trapped

■

or crushed. The hose must not come into contact with hot

surfaces.

The gas line (gas pipe or safety hose) can be connected to

■

the right or left-hand side of the appliance. The connection

must have an easily accessible locking device.

Safety information

The rated working pressure of your appliance is:

for natural gas (G20) 2 kPa;

for LPG (G30) 3 kPa;

for LPG (G31) 3,7 kPa.

Your appliance must be operated with these pressures. All the

information on the rating plate of your appliance is based on

these pressures. The manufacturer takes no responsibility for

the resulting operability or performance of the appliance or for

other risks if the appliance is operated with pressures other

than those specified.

Caution!

If the pressure of your local gas supply is higher than:

natural gas (G20) 2,5 kPa;

LPG (G30) 3,6 kPa;

or LPG (G31) 4,5 kPa; for safety reasons, the appliance must

be equipped with a suitable pressure regulator. The connection,

maintenance and setting of the pressure regulator must be

carried out by an approved gas fitter.

If you do not know the pressure of your local gas supply, ask

your gas supplier.

For your safety

This appliance is adjusted to operate on LPG only.

Faults in the gas installation/smell of gas

If you notice a smell of gas or faults in the gas installation, you

must

immediately shut off the gas supply and/or close the gas

■

cylinder valve

immediately extinguish all naked flames and cigarettes

■

switch off electrical appliances and lights

■

open windows and ventilate the room

■

call the aftersales service or the gas supplier

■

Burn back

Fire in burner tube or chamber

In the event of a burn-back, where the flame burns back to the

jet, immediately turn off the gas supply at the control valve on

the panel.

After ensuring the flame is extinguished, re-light the appliance

in the normal manner.

Should the appliance again burn back, close the control valve

and call a service technician. Do not use the appliance again

until the service technician has declared that it is safe to do so.

Gas-pressure regulator

This appliance requires an operating pressure of 2,8 kPa at the

appliance. A suitable LPG regulator that coplies with the

requirements of SANS 1237 must be installed.

Important information for the user

This appliance may only be installed by a registeres LP Gas

installer.

All registered installers are issued with a card carrying their

registration number. Ask to be shown the card before allowing

the installation work to be shown the card before allowing the

installation work to commence and make a note of the installer

QCC number.

Upon completion of the installation, the installer is required to

explain the operational details of the appliance together with

the safety instructions.

You should only sign for acceptance of the installation and be

provided with a copletion certificate. You should only sign for

acceptance of the installation when the installation is completed

to your satisfaction.

Note that your invoice is required in the event that you wish

make a quarantee claim.

Important information for the installer

This appliance may only be installed by a registered LP Gas

installer registered with the Liquefied Petroleum Gas

Association of Southern Africa.

The appliance must be installed in accordance with the

requirements of SANS 10087-1 and any fire department

regulations and/or local bylaws applicable to the area. If in

doubt check with the relevant authority before undertaking the

installation.

Upon completion of the installation you are required to fully

explain and demonstrate to the user the operational details and

safety practices applicable to the appliance and the installation.