Bose AM267565 Kullanıcı Kılavuzu - Sayfa 10

Konuşmacılar Bose AM267565 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Bose AM267565 34 sayfaları. Bose corporation user guide speaker am267565

Sayfayı Yazdır

Preparation

Figure 7

Template for either

rectangular-faced (left)

or round-faced (right)

speakers

Figure 8

Cautions against unseen

danger, such as (a) electri-

cal wires or (b) plumbing

pipes, behind the wallboard

• Each speaker enclosure extends into the wall or ceiling , as shown in the gray DO NOT CUT

area on the template (Figure 7), and below the grille. The speaker enclosure can be inserted

either up or down.

Note: In cold climates where a humidiﬁer is used, avoid inserting the speaker upside-down

in an exterior wall to prevent problems with condensation.

Allowing enough room both above and below the hole you draw provides a fallback in case

the area below your pilot hole is not suitable for the speaker enclosure.

TAPE

HERE

WARNING: Make sure the spot chosen is safe for cutting. Do not cut through

HERE

surfaces that have hazards, such as electrical wiring, conduits or plumbing,

concealed behind them. If you are not sure, consult a professional installer

before you proceed.

" (20.5 cm)

Translations below

WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical

wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.

WARNING: Make sure the spot chosen is safe for

drilling. Do not cut through surfaces that have hazards

concealed behind them, such as electrical wiring,

conduits or plumbing. If you are not sure, consult a

professional installer before you proceed.

Pilot

Hole

WARNING: Make

" (14 cm)

sure the spot chosen

is safe for drilling. Do

not cut through

surfaces that have

WARNING: Make sure the

spot chosen is safe for

hazards concealed

behind them, such

drilling. Do not cut through

surfaces that have hazards

as electrical wiring,

conduits or

concealed behind them,

such as electrical wiring,

plumbing. If you are

not sure, consult a

conduits or plumbing. If you

are not sure, consult a

professional installer

before you proceed.

professional installer before

you proceed.

WARNING: Make sure the spot

chosen is safe for drilling. Do not cut

WARNING: Make sure the spot chosen is safe

through surfaces that have hazards

for drilling. Do not cut through surfaces that have

concealed behind them, such as

hazards concealed behind them, such as

electrical wiring, conduits or plumbing.

electrical wiring, conduits or plumbing. If you

If you are not sure, consult a

are not sure, consult a professional installer

professional installer before you

before you proceed.

proceed.

DO NOT

TAPE

English & Translations

TAPE

CUT AROUND

HERE

GRAY AREA

" (36.9 cm)

9" (22.9 cm)

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

TAPE

HERE

GRAY AREA

CAUTION: When installed, the speaker enclosure cannot be seen behind the wall or ceiling.

Do not attempt to nail, cut, or drill on that surface area. Puncturing the speaker enclosure with

a tool will seriously damage the speaker.

• All electrical wiring, vents, and plumbing pipes located inside the walls must be avoided

(Figure 8). Check with a trained professional if you need instructions on how to locate and

avoid them.

(a)

(b)

• Use of a stud ﬁnder can help ensure that the speaker hole is at least 4

stud or joist.

• The selected location should be at the height you want for both speakers and where you

can maintain the minimum distance of 5 feet (1.5 m) between them.

Keeping in mind the guidelines given:

1. Decide where the ﬁrst speaker will go.

2. Select the location for the second speaker.

3. Use the provided template for drawing both a pilot hole and the speaker-face outline.

AM267565_01_V.pdf May 13, 2003

FOR CUTTING

Large white area

represents what to cut

out for the speaker face.

On the template at right,

small circles outside the

white area indicate

additional holes needed

for the round-faced

speaker only.

NOT FOR CUTTING

Large gray area

represents space to

reserve behind the wall

for the speaker

enclosure.

On the template at right,

small gray tabs also

indicate where not to cut.

WARNING: Make sure the spot chosen is safe for cutting.

Do not cut through surfaces that have hazards, such as

electrical wiring, conduits or plumbing, concealed behind

them. If you are not sure, consult a professional installer

before you proceed.

Translations below

WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical

wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.

WARNING: Make sure the spot chosen is safe for

drilling. Do not cut through surfaces that have hazards

concealed behind them, such as electrical wiring,

conduits or plumbing. If you are not sure, consult a

professional installer before you proceed.

Pilot

Hole

WARNING: Make

sure the spot chosen

is safe for drilling. Do

not cut through

surfaces that have

hazards concealed

behind them, such

as electrical wiring,

conduits or

plumbing. If you are

not sure, consult a

professional installer

before you proceed.

WARNING: Make sure the spot

chosen is safe for drilling. Do not cut

through surfaces that have hazards

concealed behind them, such as

electrical wiring, conduits or plumbing.

If you are not sure, consult a

professional installer before you

proceed.

English & Translations

TAPE

HERE

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

TAPE

CUT AROUND

TAPE

HERE

GRAY AREA

" (12 cm) from a