3M SGLP200-CL-BP Kurulum ve Kullanım Talimatları Kılavuzu - Sayfa 7
Su Filtrasyon Sistemleri 3M SGLP200-CL-BP için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları Kılavuzu indirin. 3M SGLP200-CL-BP 17 sayfaları. Reverse osmosis filtration systems
Ayrıca 3M SGLP200-CL-BP için: Kurulum Kılavuzu (17 sayfalar)
Sayfayı Yazdır
NOTICE
To reduce the risk associated with water leakage or flooding:
• Change the disposable pre-filter at the recommended interval; the disposable pre-filter MUST be replaced
every 12 months or sooner.
• Change the disposable filter RO membrane at the recommended interval; the disposable RO membrane MUST
be replaced every 24 months or sooner.
• Failure to replace the disposable pre-filter and RO membrane at recommended intervals may lead to reduced
filter performance and failure of the filter, causing property damage from water leakage or flooding.
This product is outfitted with user friendly 'Push In' connectors. Proper use of the connectors is shown in the
diagrams. It is most important that the tubing selected for use with these connectors be of high quality, exact size
and roundness, and with no surface nicks or scratches. If it is necessary to cut the tubing, use a plastic tubing cutter
or sharp razor knife. Make a clean square cut.
Should a leak occur at a 'Push-In' connector, the cause is usually a problem with the tubing.
To Fix: 1. Relieve pressure.
4. Reattach tubing
o T
A
a t t
h c
u T
i b
g n
1
O-Ring
Tube
Grey Collet
Push tubing straight in as far
as it will go.
1. Remove the pre-filter cartridge from its packaging. Remove the red cap from the cartridge and moisten the
o-rings with water. Insert the cartridge into the filter head. Then, turn the cartridge 1/4 turn to the right.
2a. For SGLP100-CL, remove the red cap from the RO-membrane cartridge and moisten the o-rings with water.
Insert the cartridge into the filter head. Then, turn the cartridge 1/4 turn to the right.
2b. For SGLP200-CL and SGLP200-CL-BP, remove the red caps from both the RO-membrane cartridges and moisten
the o-rings with water. Insert the RO-membrane cartridges into the filter heads. Ensure that the RO-cartridge
with the blue-control is inserted into the RIGHT-side head, while the other RO-membrane cartridge is inserted
into the LEFT-side head. Turn both the RO-membrane cartridges 1/4 turn to the right.
3. Check that all plumbing connections are secure.
4. Open the tank shut-off valve. Turn on the incoming water supply or beverage booster pump (if applicable) and
check the system for leaks. If any leaks are noted, turn off the water supply and/or booster pump and correct
the leak before proceeding. If a leak is detected at a push-in fitting, refer to Figure 2.
5. Open downstream valve (not included) and let water run through the RO to drain for 10 minutes.
6. Close sample valve.
7. Allow tank to fill (Approximately 60 minutes).
8. Open Water Sample Valve outlet to drain. Empty tank. Water flowing from tank will reduce to a fast drip when
tank is empty.
9. Allow product water to run to drain for 24 hours.
10. Close sample valve and allow the tank to fill (Approximately 60 minutes).
11. System is now ready for use.
HOW TO USE 'PUSH-IN' FITTING
2. Release tubing
5. Confirm connection is leak free
o T
2
1
Tubing is secured in.
Push in collet to release tubing.
Figure 2
SYSTEM START-UP
6
3. Cut off at least 1/4"from end
R
l e
a e
e s
u T
i b
g n
2
Pull tubing straight out.