Bose 1800-VI Kullanıcı El Kitabı - Sayfa 13

Amplifikatör Bose 1800-VI için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Bose 1800-VI 32 sayfaları. Professional stereo power amplifier
Ayrıca Bose 1800-VI için: Hızlı Kılavuz (2 sayfalar), Kurulum Hizmetleri (4 sayfalar)

Bose 1800-VI Kullanıcı El Kitabı

4.8.3 Bridged mono

1800 SERIES VI PROFESSIONAL AMPLIFIER
FOR BRIDGED
OPERATIONS
SER.
CONSULT
NO.
MANUAL
ON
OFF
BOSE CORPORATION, FRAMINGHAM, MA 01701-9168 MADE IN U.S.A.
LEVEL DEFEAT
INPUT IMPEDANCE 25K OHMS EACH LEG TO GROUND (TOTAL 50K OHMS BALANCED)
SEND
RECEIVE
PUSH
INPUT CH2
INPUT CH1
SEQUENCE
2
1
EQUALIZATION ON
CH1
3
2
1
CH2
3
CH2
CH1
EQ. OUT
Use CH 2
only for input
The stereo/mono switch is located on the input board behind slot #2 of the standard input
module (or, on the AMC-1 module, to the left along the rear edge of the board). For bridged-
mono operation, move the STEREO/MONO switch all the way to the right to the BRIDGED
setting (or, on the AMC-1 module, move that switch all the way to the left). Connect the
input signal to CH 2 input (CH 1 input becomes disabled). Connect the speakers to the two
+ speaker terminals. The CH 2 + terminal is the hot (non-inverting) side, and the CH 1 +
terminal is the low (–, inverting) side (see Figure 8).
When connected in this way, each channel "sees" half the impedance of the speaker
connected between them. If you use an 8 ohm speaker, each channel will see a 4 ohm load.
Therefore it is not recommended that you use any load lower than 8 ohms in this mode of
operation. Use parallel mono operation for lower impedances.
Note
Be sure to set both of the input level controls to the exact same setting for equal power
distribution per channel. Switching the level defeat switch (located on the amplifier) to OFF
will assure that both channels are operating at the same level.

4.8.4 Parallel mono

Parallel mono operation is useful when running sustained high levels in a single load or
when driving a low impedance load.
For instructions, contact Bose

4.9 Clipping eliminator

This circuit prevents the input signal from exceeding the point where it would drive the
amplifier into hard clipping. It has no effect until the signal reaches the clipping point. The
larger the input signal, the more it is reduced to keep the output just below clipping.
The clipping eliminator circuit is operational at the point of manufacture. However, you can
defeat it by using the clipping eliminator defeat switch. This switch is located on the rear
panel of the amplifier. Moving the switch up will re-engage the clipping eliminator.
Note
If you turn the input level down far enough, a sufficiently large input signal can drive the input
differential amplifier into clipping. The clipping eliminator circuit cannot remedy this. It also has
no effect on clipping that occurs prior to the amplifier inputs, such as at the mixer or equalizer.
WARNING
ADVERTISEMENT
RISK OF HAZARDOUS ENERGY! MAKE PROPER
ENERGIE ELECTRIQUE DANGEREUSE.
SPEAKER CONNECTIONS. SEE OPERATING
D.O.M.
MANUAL BEFORE USING.
LICENSED UNDER U.S. PAT. NO. 4,484,150
ON
CLIPPING
PUSH
ELIMINATOR
CAUTION
AVIS
OFF
RISK OF ELECTRIC SHOCK
RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN
NE PAS OUVRIR
2
1
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
3
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
GND
®
or your authorized Bose Professional Products dealer.
BRIDGED
1400 W 8
700 W 4
700 W 4
200-240 V
AC
50-60 Hz
1800 W
CH 2
CH 1
SPEAKER OUTPUTS
CLASS 1 WIRING SHALL BE USED
To "+"
To "–"
speaker
speaker
terminal
terminal
4.0 Installation
Figure 8
Bridged mono connection.
CAUTION
In bridged mono operation,
the output connections are
actually a balanced output
configuration. This means
both output terminals have
voltage present (neither may
be grounded).
13