Dromex DFA-PN21 Manuel - Sayfa 2

Güvenlik Ekipmanları Dromex DFA-PN21 için çevrimiçi göz atın veya pdf Manuel indirin. Dromex DFA-PN21 2 sayfaları. Fall protection harness

Sayfayı Yazdır

In order to maximise the harness life cycle, we recommend the mildest possible cleaning

conditions in terms of temperature, chemicals and cycle duration.

Due to a wide variety of possible constructions and combinations with other materials we

recommend to always consult your professional cleaning service to determine the best

suitable cleaning method.

Shelf life

All soft goods, including harness, can be used for ten years from the date of ﬁrst use as long

as they are examined by a qualiﬁed individual who has been trained by the manufacturer

in accordance with EN365 requirements. After ten years OR if it doesn't pass the competent

person examination, the product must be taken out of service. '

Ensure product storage guidelines are followed.

The following factors can reduce the Lifespan of the product; intense use, contact with

chemical substances, especially aggressive environment, extreme temperature exposure,

UV exposure, abrasion, cuts, violent impacts, bad use, or maintenance.

Remove and replace once the energy absorber has been deployed.

Sizes Available

Standard - Universal.

Instructions to be followed before use

• It is important to carry out a pre use check of the equipment to ensure that it is in a

serviceable condition.

• Inspect the harness and the lanyard for any rupture of webbing, rope, seams, buckles,

D-ring etc. Do not use in case of any rupture or defectiveness.

• In case of any doubt arising about the condition of any component or system, replace it

immediately. If the harness has arrested a fall, or if the impact/load indicator has

accidently been deployed during handling, withdraw it from service & return to the

manufacturer or a competent repair center.

• It is essential to ensure that there is a minimum clearance of 6m beneath the user at the

work place before each occasion of use, so that in case of a fall, there will be no collision

with the ground. Also, ensure that no obstacle exists beneath the user at his workplace

so that he does not collide with any, in case of a fall.

• Prior to use of the harness the user should carry out a suspension test in a safe place to

ensure that the harness is the correct size, has suﬃcient adjustment, and is of an

acceptable comfort level for the intended use.

• Apart from Fall Arrest this harness can be used for speciﬁc situations in conjunction with

Fall Arrestors where the front attachment is needed.

• Both leg straps, chest strap, shoulder strap and waist belt are adjustable to ﬁt the size of

the user.

• A harness that is either too loose or too tight will restrict movement and will not provide

the optimum level of protection.

• The size of the harness is marked on a label attached to it and it is universal.

Putting on the Harness

Step 1

Step 2

Step 3

Untangle the

Insert your arms one by one into the shoulder

harness by

straps.

holding it from

the dorsal D-ring.

Step 5

Step 6

Step 7

Pull the leg straps

To check & adjust all the straps of the harness to your body adjustment, refer

one by one around

to Step 6 to Step 8.

your thigh outwards

to your front.

NOTE: After putting on the harness, user should carry out a comfort and adjustability test in a

safe place by sitting & bending forward to ensure that the harness is in the correct size and

and has sufficient adjustment and is of an acceptable comfort level for the intended use.

To locate the anchor point on the harness, check for the "A" marking near them.

Periodic Examination

• This product needs to be periodically examined because the safety of the user depends

upon the continued eﬃciency and durability of the lanyard.

• It is important to examine it at least once in every 12 months.

• Periodic examination is to be conducted by a competent person and strictly in accordance

with the manufacturer's periodic examination procedures.

• Periodic examination also requires checking the legibility of the product markings

• Always retain a copy of the Harness Equipment Perodic Examination and Repair History

checklists.

Ground Clearance

Drawing

Impact

distribution

Step 4

plate

Adjustable

chest straps

with buckles

Lanyard

keepers

Close the buckle

Adjustable

on the chest strap.

shoulder straps

with buckles

Adjustable leg

Step 8

straps with

buckles

Sit strap

NOTE: Chest, shoulder, leg straps and waist belt are all feature metal parachute buckles and

plastic keepers.

Marking

(ii)

full body harness

Unit 1, 1 Blasé Road, New

Germany, South Africa, 3620

(i) (x)

(iii)

Type

DFA-PN21

(iv)

Mfg. mm/yy

XX/XXXX

(v)

Batch no.

XXXX

(vi)

Serial no.

XXXX

(vii)

Material

Polyester

(viii)

Length

1.75 m

Marking on Product

The Energy Absorbing Lanyard is marked with:

(i)

The CE mark showing that the product meets the requirement of the European PPE

Regulation (EU) 2016/425

(ii)

Identiﬁcation of the manufacture and address

(iii)

Type of product code

(iv)

Month & Year of Manufacture

(v)

Batch/Lot Number

(vi)

Serial Number

(vii)

Material

(viii) Length

(x)

Norm

Yellow

Disposal

webbing

Industrial harnesses should be disposed of considering the hazardous substance they were

harness

used for, if damaged and once the shock absorber has been deployed.

Dorsal D ring

Please consider recycling.

Steps for safe Disposal:

• Segregate the equipment in three diﬀerent crates for placing components

in them respectively such as - Textile, Metal and Plastic.

• Inspect the wear and tear present on the harness and lanyard by holding

the harness on the D ring

• Using a sharp pair of scissors to cut the Textile and dismantle the harness

Steel scaffold

& lanyard.

hook

• Thereafter remove the metal & plastic components separately from the

harness & lanyard.

• Put the Textile, Plastic & Metal components in their respective plastic crates.

• Once segregation done, arrange to send them for recycling or

Energy absorber

disposal (as appropriate) through authorized agencies as per local or

national.

Waist belt

Dromex: Unit 1, 1 Blase Road, New Germany, 3620, South Africa

T. +27(31) 713 1960 E. [email protected]

Disclaimer

Dromex reserves the right to make changes without further notice to any products herein to improve function, design or reliability

and validity. Dromex does not assume any liability arising out of the application or use of any product described herein.

Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.

(i)

Type

DFA-PN21

(iii)

(iv)

Mfg. mm/yy : XX/XXXX

(v)

Batch no.

: XXXXX

(vi)

EN 361:2002

(x)

Serial no.

: XXXX

Material

: Polyester

(vii)

(viii)

Size

: Universal

Max. Rated Load

Made In India

(Including all tools)

CODE

(ii)

Batch no. : XXXX

Serial no.:XXXX

to be used only in vertical fall arrest systems

Unit 1, 1 Blasé Road, New Germany, South Africa, 3620

minimum ground clearance from anchorage point : 6.0 m

2.0 m (max)

1.2 m (max) Break distance

1.8 m body

1.0 m safety distance

www.dromex.co.za

Latest update: 13/06/2023