Elekit 6L6GC Montaj ve Kullanım Kılavuzu - Sayfa 2

Amplifikatör Elekit 6L6GC için çevrimiçi göz atın veya pdf Montaj ve Kullanım Kılavuzu indirin. Elekit 6L6GC 2 sayfaları. Single stereo tube power amp

Sayfayı Yazdır
Before you solder
Before you solder, follow the cut line (grooved line) to break the circuit boards TU
Before you solder, follow the cut line (grooved line) to break the circuit boards TU-879R A-E into individual pieces.
There are grooved lines on both sides of the circuit board. Gently use the
There are grooved lines on both sides of the circuit board. Gently use the edge of a table to break them.
2. Circuit Board Assembly
A Circuit Board Assembly
Preparations before you begin
On the soldering side (side with copper foil) of circuit board
On the soldering side (side with copper foil) of circuit board A, there are 3 holes with arrows indicated.
Solder plate the 2 holes with copper foils.
1. Diode (direction specific)
/
The line is on the side of K
D1
Marked on PCB
How to install
4. Bridge Rectifier
(direction specific)
+,- indication
Please pay attention! It is
\
dangerous if the rectifier is not
installed properly.
D2, 3
Marked on PCB
How to install
Bend the legs on the back of the PCB
to prevent it from falling out when
soldering on the copper foil.
6. Ceramic Capacitor
(non direction specific)
C7, 8
220pF (with indication of 221)
Marked on PCB
How to install
© EK Japan 2005
TubeDepot.com
TubeDepot.com
Follow the instructions step
Follow the instructions step-by-step. Check off the box after you
have soldered each component.
have soldered each component.
When soldering, be sure to read "The Key to Soldering."
When soldering, be sure to read "The Key to Soldering."
SG (2 places)
SG (2 places)
2. Resistor
(non-direction
Resistor
Resistor
(Carbon)
R1,9,10,11,12
R1,9,10,11,
330kΩ
(Orange, Orange, Yellow, Gold)
R3,4,25,25
R3,4,25,25
2kΩ
2k
(Red, Black, Red, Gold)
R5,6,23
R5,6,23
3.3
3.3Ω
(Orange, Orange, Gold, Gold)
R7,8,15
R7,8,15
120
120Ω
(Brown, Red, Brown, Gold)
R20,21,22
R20,21,22
2.2MΩ
2.2M
(Red, Red, Green, Gold)
Resistor
Resistor
(metal oxide film)
R16,18,19
R16,18,19
15kΩ(2W)
Install the metal oxide
R13,14
R13,14
330
330Ω(3W)
film resistor 2-3mm above
the PCB to diffuse heat.
R17
R17
3.3kΩ(5W)
3.3k
Marked on PCB How to install
Marked
Carbon resistor
5. Fuse holder
. Fuse holder
(direction specific)
Marked
Marked on PCB
How
How to install
Where the fuse holder (metal
Where the fuse holder (metal
fitting) is placed, please
fitting) is placed, please pre-apply
a thick layer of solder plate on the
a thick layer of solder plate on the
oval shaped copper foil.
oval shaped copper foil.
7. Base pin
. Base pin
Install from solder side (reverse side), total of 12
Install from solder side (reverse side), total of 12
OPT1(L) P 3 pcs
OPT1(L) P 3 pcs
OPT1(L) B 3 pcs
OPT1(L) B 3 pcs
OPT2(R) P 3 pcs
OPT2(R) P 3 pcs
OPT2(R) B 3 pcs
OPT2(R) B 3 pcs
Install from the side with
Install from the side with white printing, total of 3
FET G, D, S
FET G, D, S
Marked on PCB (FET only)
Marked
E into individual pieces.
3. Jumper wire
Jumper wire
Marked on PCB
PCB
How to install
(1)
Cut 7 strands of tin-coated wire 6-7cm in length.
Cut 7 strands of tin
(2)
Put a strand of tin
Put a strand of tin-coated wire into a plastic tube
and bend to the shape in the image below. The
total length of the product should be 35mm. Use
total length of the product should be 35mm. Use
long nose pliers to bend.
long nose pliers to bend.
(not actual size)
(3)
Solder the jumper wires onto the PCB the same way as the resistors
Solder the jumper wires onto the PCB the same way as the resistors
FUSE 1, 2
Set the 5x20 GMA fuse to two fuse holders
to two fuse holders
and put the legs through the holes on the PCB
from the solder side.
Bend the legs using long nose pliers to
Bend the legs using long nose pliers to
station it on the PCB. Take the 5X20 GMA
5X20 GMA fuse
from the fuse holder and solder the fuse
from the fuse holder and solder the fuse
holders onto the copper foil.
Reinstall the 5X20 GMA fuse after soldering.
fuse after soldering.
FUSE1 →0.3A FUSE2 → 2A
Caution: 12 pins are installed from the solder side (with copper foil)
Caution: 12 pins are installed from the solder side (with copper foil)
and 3 pins are installed from the side with white printing.
and 3 pins are installed from the side with white printing.
Marked on PCB
Insert the pin
perpendicularly into
the hole on the PCB.
Always solder on the
Always solder on the
solder side (reverse
side) regardless of
which side the pin is
inserted from.
1686 Barcrest Drive, Memphis, TN 38134
1686 Barcrest Drive, Memphis, TN 38134
(non-direction specific)
the shape in the image below. The
s on the PCB
2A
Put the PCB on a
piece
of
cardboard
when
installing
pins. Use long nose
pliers to insert the pin.
Do
not
cut
protruding base pin
after soldering.
3
J1-7
the
the