DryBell Vibe Machine V-2 Seçenek Kılavuzu - Sayfa 8
Müzik Pedalı DryBell Vibe Machine V-2 için çevrimiçi göz atın veya pdf Seçenek Kılavuzu indirin. DryBell Vibe Machine V-2 18 sayfaları.
Ayrıca DryBell Vibe Machine V-2 için: Kullanıcı Kılavuzu (2 sayfalar)
Sayfayı Yazdır
DryBell Guitar Effects
6 SETUP MODE
SETUP MODE is a system that is used to set and save additional secondary settings embedded in the V-2
hardware/firmware structure
advanced and curious users and their specific needs.
The basic principle of changing any setting via SETUP MODE is to enter and select the desired SETUP MODE menu,
set the desired parameter or setting, and save it by pressing the footswitch on the pedal.
If for any reason a user wants to quit their current SETUP MODE programming procedure without setting and saving,
the CHORUS/VIBRATO switch should be toggled. The setup procedure will then be cancelled and the V-2 pedal will use its
last saved setting. So, if you are in any setup menu, and toggle the CHORUS/VIBRATO switch, it acts like a general EXIT
command without saving anything.
6.1
HOW TO ENTER SETUP MODE MENU?
The SETUP MODE menu can be entered within 4 seconds after toggling the CHORUS/VIBRATO switch by pressing
the footswitch quickly 4 times. Entering SETUP MODE is visually indicated with LED briefly blinking orange (5x).
The SETUP MODE system has two menus. For MENU 1 the system LED is red, and for MENU 2 the system LED is
green. Each menu has 10 positions for setting different parameter values. Position 10 in MENU 1 is for entering
MENU 2.
After entering the SETUP MENU the user goes through the SETUP MENU positions by rotating speed pot. On odd
positions the system LED is constantly ON, and on even positions the system LED is flashing. After selecting the
desired SETUP MENU position (by rotating the speed pot), that position is selected for editing by pressing the
footswitch. Then the user must use Table 2 below
selecting the desired parameter (by rotating the speed pot again) the user must press the footswitch to save the
new parameter value into the pedal's memory and then the pedal will continue to work normally.
6.2
EXAMPLE OF CHANGING SETUP PARAMETER
If you don't have an expression pedal at the moment, but you own a passive volume pedal, and you are curious as
to how the Vibe Machine works with an expression pedal...? Yes! This can be done. With a simple TRS Y cable you can
connect your volume pedal to the Vibe Machine V-2 and use it like an expression pedal. But you must 'instruct' the V-2
pedal that you have connected a volume pedal to the PEDAL+ jack instead of a linear passive expression pedal.
The procedure for changing exp. pedal taper types is as follows:
1)
Toggle C/V switch and press the footswitch 4 times quickly to enter SETUP MENU 1
2)
Rotate the speed pot to position 1 (E1 mark on silkscreen,
3)
Press the footswitch to enter the expression pedal potentiometer selection menu (E1)
4)
Rotate speed pot to position T9 or T10 (volume pedal taper,
5)
Press the footswitch again to confirm and exit to normal operation
Now you can use your volume pedal as if it were an expression pedal.
6.3
VIBE MACHINE V-2 SETUP MENU OPTIONS TABLE
If the column named "PARAMETER POSITIONS AROUND THE SPEED POT" in Table 2 shows several possible
positions around the speed potentiometer for the same parameter (for example Setup mode 4 (S4): "S6, X7, T8, T9, T10:
MOMENTARY FOOTSWITCH"), that means you can choose any of those positions shown in the table for the same
parameter. So, if you want to set the external footswitch type to momentary type you can rotate and set the speed pot to
any possible position S6, X7, T8, T9 and T10 (and between). After that press the footswitch to save and exit setup
procedure.
On the bottom of the table there are a few Factory modes. Factory modes are used only for adjusting internal
factory parameters, which only we can adjust in production and after production testing processes. They are not important
to the user.
BACK TO CONTENTS
www.drybell.com
(Table 2, Pages
9-11). The average user probably won't use them, but they are here for all
DryBell
Vibe Machine V-2, Options User's manual, rev.1.4. 09/2018
(Page
9) to change the values of their desired settings. After
Table
2)
Table
2)
Doc. No. DM0958/ Page 8