DS DS7445i Kurulum Talimatları - Sayfa 4

Tuş takımı DS DS7445i için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. DS DS7445i 4 sayfaları. 4-wire alpha-numeric lcd keypad

Sayfayı Yazdır

8.0

Commercial Fire Applications

(DS7400Xi Series)

8. 1

Single Keypad Use in Commercial Fire

Systems

The keypad must be used on the keypad bus and mounted

to the front of the control enclosure. If the keypad is within

the same room as the control equipment, with the wire run

in conduit (or equally protected against mechanical injury)

within 6 m (20 ft.) of the control equipment.

The keypad must be assigned as Keypad Address 1.

8.2

Multiple Keypad Use in Commercial Fire

Systems

Only one keypad must be used on the panel's option bus

and assigned as Keypad Address 11-14.

The keypad must be mounted to the front of the control

enclosure. If the keypad is within the same room as the

control equipment, with the wire run in conduit (or equally

protected against mechanical injury) within 6 m (20 ft.) of

the control equipment.

9.0

Instruction Label and Slide

Two instruction labels are provided and one must be placed

onto the pull-out slide. The slide may be installed to pull

from the left or the right (slide it into rear of base).

Figure 8: Instruction Label and Slide Installation

1 - Back of keypad

2 - Pull-out slide

3 - Instruction label (Writing on other side)

4 - Pull-out slide guide track

5 - Alternate location of pull-out slide

•

Use Instruction Label (P/N: 28815) if the keypad(s) you

are installing are for use with the DS7060, DS7080i

Series and DS7400Xi Series Control Panels.

•

Use Instruction Label (P/N: 49646) if the keypad(s) you

are installing are for use with the DS7200 Series

Control Panels.

130 Perinton Parkway, Fairport, NY 14450-9199 USA

Customer Service: (800) 289-0096; Technical Support: (888) 886-6189

Be careful when installing the label. Place it as

close to the pull-tab as possible.

10.0

Troubleshooting

See Table 5 for troubleshooting tips.

Table #: One-column Wide

Keypad Notification

DS7445i Continuous

Sounder.

DS7447i/DS7447E

Continuous Sounder and

System Fault display.

DS7445I Continuous

Sounder

DS7447i/ DS7447E

Continuous Sounder and

Not Programmed Display.

DS7445i 3-beep Error Tone

on All Keypads.

DS7445i/DS7447i/

DS7447E

3-beep Error Tone on All

Keypads and Entry

Error. Please Try

Again Display on

DS7447i/DS7447E Keypad.

P/N: 49205D

Installation Instructions

Possible Causes

The yellow and green wires

have been disconnected

The control panel has

malfunctioned. Replace the

control panel.

The yellow and green wires

have been disconnected

The control panel has

malfunctioned. Replace the

control panel.

The keypad has not been

programmed properly at the

control panel.

The keypad has not been

programmed properly at the

control panel.

Two or more keypads have the

same address.

DS7400 Series Only: DS7430

MUX Module not installed

on main board correctly.

Check pin alignment.

DS7400 Series Only: Keypad

and another device on the

option bus have the same

address.

Two or more keypads have the

same address.

DS7400 Series Only: DS7430

MUX Module not installed

on main board correctly.

Check pin alignment.

DS7400 Series Only: Keypad

and another device on the

option bus have the same

address.

Keypads - DS7445i/DS7447i/DS7447E

Page 4 of 4

7/03