Daintree GE current 93013522 Kurulum Kılavuzu - Sayfa 4

Fener Daintree GE current 93013522 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Daintree GE current 93013522 4 sayfaları. Led luminaire

Sayfayı Yazdır

Lumination

(Tetra

Electrical Connections

Strip the ends of the wire 1/2-inch (13 mm) on the modules

(white and red) of adjacent columns that you want to connect.

Use UL approved wire connectors (twist-on or in-line connectors)

and 18 AWG (0.82 mm

) wire to connect the corresponding wires.

Strip the end of the wire 1/2-inch (13 mm) on the first column

of modules and connect to the output of the LED Driver. Output

connections must be red-to-red and white-to-black.

Refer to the LED Driver Installation Instructions for

more information on connecting the LED Driver.

Troubleshooting

Symptom

Row of modules does not light

All modules do not light

Individual modules do not light

Modules are dim

Loading Chart

LED Driver

79045 (GE080/MV/D24T1-A)

67825 (GEPS24-100UGL-IP)

62189 (GE180/MV/V24T1-C)

Remote Mounting Distance

LED Driver

79045 (GE080/MV/D24T1-A)

67825 (GEPS24-100UGL-IP)

62189 (GE180/MV/V24T1-C)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class [A] RFLD complies with the

Canadian standard ICES-003. Ce DEFR de la classe [ A ] est conforme á la NMB-003 du Canada.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

PowerGrid - Series)

• Check wire connections to LED Driver to ensure red-to-red and white-to-white connections.

• Check row-to-row polarity connections.

• Check input voltage and check LED Driver input/output connections.

• Check wire connection attachment and polarity of wires.

• Ensure the overall length of modules does not exceed the maximum load for the LED Driver.

• Ensure the length of the supply wire is equal to or below the recommended remote mounting distance

(see remote mounting distance chart above).

Minimum Loading

1 Module

18 AWG (0.82mm

Supply Wire

1-30 ft. (0.3-9.1m)

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without

notice. All values are design or typical values when measured under laboratory conditions.

ARCH015 (Rev 04/02/2021)

LED Driver

Solution

33 Modules/22 ft. (6.7m) per Bank; 66 Modules/44 ft. (13.4m) per Driver

)

16 AWG (1.31mm

)

14 AWG (2.08mm

Supply Wire

1-50 ft. (0.3-15.2m)

Installation Guide

Wire connections

Cap all unused wires

Maximum Loading

30 Modules/20 ft. (6.1m)

36 Modules/24 ft. (7.3m)

)

12 AWG (3.31mm

Supply Wire

1-80 ft. (0.3-24.4m)

1-120 ft. (0.3-36.6m)

)