Daintree GE current Tetra GEPS24-180U Kurulum Kılavuzu - Sayfa 2

Güç Kaynağı Daintree GE current Tetra GEPS24-180U için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Daintree GE current Tetra GEPS24-180U 3 sayfaları. Led systems power supply

Sayfayı Yazdır

Tetra

Power Supply GEPS24-180U

RISK OF ELECTRIC SHOCK

• Disconnect power at fuse box or circuit breaker before servicing or

installing product.

• Properly ground Tetra

power supply.

RISK OF FIRE

• In the end product, power supply spacing to other heat producing

components shall be minimum 2 inches spacing to sidewalls, and

minimum 2 inches spacing to top of enclosure.

• Adjacent power supplies shall be spaced at least 1 in. end to end

and 4 in. in any other direction.

• Use only approved wire for input/output connection. Minimum

size 18 AWG (0.82 mm

• Follow all local codes.

• Application considerations potentially requiring additional spacing

include high ambient temperature seen by the power supply, poor

contact with a heat dissipating material, inadequate ventilation, or

direct exposure to sun.

RISK INJURY

• While performing installations described, gloves, safety glasses or

goggles should be worn.

Power Supply Installation

Remove the junction box cover and

carefully remove knockout for AC line

input wires. Install appropriate electrical

fittings in the knockout holes for wire

protection. Securely mount the power

supply with the base in contact with the

mounting surface in accordance with

the power supply spacing requirements

described above. If used in a wet

location, the power supply and electrical

connections shall be protected from

weather by a suitable rain enclosure, and

not subject to saturation with water or

other liquids. If not protected from the

weather, the output connections may be

sealed with electrical grade silicone.

NOTE: For CSA approval, a disconnect/toggle switch of appropriate rating needs to be placed within 29.5 ft. (9 m) of primary

FOR UL ONLY

side of the power supply. The minimum rating of the switch must be either 120 or 220 Volts AC. The switch must also support

twice the amount of input current.

NOTE: When installing power supply, connect to the appropriate sized building breaker or disconnect device for line and

FOR UL ONLY

neutral connections, in accordance with local, state or country regulations.

NOTE: The grounding and bonding of the power supply and overall sign shall be done in accordance with National Electric

FOR UL ONLY

Code (NEC) Article 600.

OPTIONAL

A Weather Box (GEXNWB2) may be used to house and seal Class 2

connections.

A) Insert wire connectors into weather box. Fill with electrical grade

silicone and close box.

B) Secure the weather box using a #6 or #8 (M2 or M3) screw.

WARNING / AVERTISSEMENT

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l'alimentation électrique à la boîte de fusibles ou au disjoncteur avant

l'entretien ou l'installation du produit.

• Assurez-vous de correctement mettre à terre le bloc d'alimentation Tetra

RISQUES D'INCENDIE

• Dans le produit fini, l'espacement entre le bloc d'alimentation et les autres

composants dégageant de la chaleur doit être d'au moins 2 pouces des

parois latérales et d'au moins 2 pouces du haut de l'enceinte.

• Les blocs d'alimentation adjacents doivent être espacés d'au moins 1 po

de bout en bout et 4 po dans toute autre direction.

• N'utilisez que des fils approuvés pour les entrées/sorties de connexion.

Taille minimum 18 AWG (0.82 mm

• Respectez tous les codes locaux.

• Certaines applications pourraient requérir un espacement additionnel, p.

ex. une température ambiante élevée autour du bloc d'alimentation, un

mauvais contact avec une matière dissipatrice de chaleur, une ventilation

inadéquate ou une exposition directe au soleil.

CAUTION / ATTENTION

RISQUES DE BLESSURE

• Lors de l'exécution des installations décrites, des gants, des lunettes de

sécurité ou des lunettes de protection doivent être portées.

To LED system

Output wires

Connect the supply wire that is

attached to your LED system to the red

(+) and black (-) output wires of the

LED driver as outlined in the "Electrical

Connections" section of your LED

system's Installation Instructions.

Installation Guide

Green with

yellow

stripe

(ground)

White (neutral)

Black (line)

Connect the AC line to the black

(line) and white (neutral) input

wires of the LED driver using

18-14 AWG (0.82-2.08 mm

) twist-on

wire connectors. Ground LED driver

by connecting green wire with yellow

stripe to grounding screw. Replace

junction box cover.

NOTE: To avoid overloading this

power supply with LED modules,

please refer to the specific module

loading guides.

Weather box

can be painted

Light engine

AC line