Daintree GE current WGA100 Kurulum Kılavuzu - Sayfa 9

Adaptör Daintree GE current WGA100 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Daintree GE current WGA100 9 sayfaları. General purpose adapter

Sayfayı Yazdır

Daintree

Networked General Purpose Adapter (WGA100)

Troubleshooting

The Installation Test procedure fails.

1. Confirm that the WGA100 is powered.

2. Check the connections from the WGA100 to the devices.

3. Check to be sure the WGA100 DIP switch settings are correct.

4. Press and hold the Reset button for 3 seconds to reset

the WGA100.

5. Perform the Installation Test again.

Class A Digital Device (CE)

WARNING

This is a class A product. In domestic environments this product may

cause radio interference in which case the user may be required to

take adequate measures.

FCC Warning Message

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and radiates radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encourage to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna;

• Increase the separation between the equipment

and receiver;

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected;

• Consult the dealer or an experienced radio/TV technician

for help.

Industry Canada (IC) Warning Message

Product complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesired operation. CAN ICES-005 B / NMB-005 B

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation

or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's purposes, the matter should be

referred to GE Current, a Daintree company.

Input Voltage

Switched Output

Relay

Low Voltage

Output

Analog Output

Analog Input

Binary Inputs (2)

Binary Output

Radio Properties

Operating

Environment

Compliance

Mounting

Dimensions

Low Voltage

Wiring

WGA100

CAUTION

RISK OF EXPOSURE IF BATTERY IS REPLACED BY AN

INCORRECT TYPE. DISPOSAL OF USED BATTERIES

ACCORDING TO THE INSTRUCTIONS.

Questions:

Web: products.gecurrent.com

Phone: 1-866-855-8629

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without notice.

All values are design or typical values when measured under laboratory conditions.

DT110 (Rev. 04/29/2021

Installation Guide

Specifications

120-277VAC, 50-60Hz

15A @ 120-277 VAC

1 hp @ 120-230 VAC

24VDC; 75mA maximum

0-10VDC, 5mA max

0-10VDC

Active high.

LSD (low side driver) aux relay control,

75mA maximum (including attached

sensors)

2.4 GHz, +8 dBm, Range dependent

on RF propagation variables such

as metal obstacles

Indoor, dry location

-4° to 149°F (-20° to 65°C)

CSA certified, plenum rated,

FCC Part 15, CA IC

1/2" knockout, screw tab, optional

mounting bracket supplied

9.4" L x 1.7" W x 1.18" H

10.1" L x 1.7" W x 1.18" H with

mounting bracket

Max. recommended length of up

to 100' (30m)