DSC PowerSeries LCD5511 Kurulum Talimatları - Sayfa 2

Güvenlik Sistemi DSC PowerSeries LCD5511 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. DSC PowerSeries LCD5511 4 sayfaları. Dsc lcd5511 keypad instruction manual
Ayrıca DSC PowerSeries LCD5511 için: Kullanım Kılavuzu (20 sayfalar), Kullanım Kılavuzu (12 sayfalar), Kurulum Talimatları (4 sayfalar), Kurulum Eklentileri (4 sayfalar), Kullanma (2 sayfalar)

Sayfayı Yazdır

DSC PowerSeries LCD5511 Kurulum Talimatları

4. If the 'Z/P' terminal is programmed as an output, the output follows the PGM programmed in Section

INSTALLATION INSTRUCTIONS

[000][8]. A small relay, buzzer or other DC operated device may be connected between the positive

The LCD5511 keypad presents system status using an LCD display along with symbols and numbers. The

supply voltage and the 'Z/P' terminal (maximum load is 50mA).

keypad can be used on security systems with up to 64 zones. The LCD5511 is compatible with the follow-

Applying Power

ing DSC security systems:

Once all wiring is complete, apply power to the control panel:

• PC580/PC585

• PC5008

• PC1616

• PC1864

1. Connect the battery leads to the battery.

• PC1555/PC1565

• PC50XX

• PC1832

2. Connect the AC transformer.

For more information on control panel power specifications, see the control panel Installation Manual.

Specifications

NOTE: Do not connect the power until all wiring is complete.

• Voltage rating: 12V

nominal

• Connects to control panel via 4-wire Keybus

Enrolling the Keypad

• One keypad zone input/PGM output

Once all wiring is complete, you will need to enter a 2-digit number that tells the system the partition and

• Current draw: 22mA (standby) / 85mA (maximum)

slot assignment of the keypad.

• Optional tamper version

If your system has partitions, you will need to also assign the keypad to a partition (1st digit).

• Four programmable function keys

The slot assignment (2nd digit) tells the panel which keypad slots are occupied. The panel can then gen-

• Ready (green) and Armed (red) status lights

erate a fault when a keypad supervisory signal is not present. There are eight available slots for keypads.

• Low temperature sensor

LCD5511 keypads are always assigned to slot 1 by default. You will need to assign each keypad to its

• Dimensions: 75 x 120 x 25mm (WxLxD)

own slot (1 to 8).

• Weight: 120g

Enter the following at each keypad installed on the system:

1. Enter Installer Programming by pressing [*][8][Installer's Code]

Installation

2. Press [000] for Keypad Programming

Unpacking

3. Press [0] for Partition and Slot Assignment

The LCD5511 package includes the following parts:

4. Enter a two digit number to specify the partition and slot assignment.

• One LCD5511 keypad

• one tamper switch

NOTE: If your system does not have partitions, enter [1] for the first digit.

• Four mounting screws

• surface tape

1st digit: Enter 0 to 8 for partition assignment (0 = Global Keypad).

• one end-of-line resistor

• one Installation Manual

• three keypad inner door labels

2nd digit: Enter 1 to 8 for slot assignment.

5. Press the [#] key twice to exit programming.

Mounting

6. After assigning all keypads, perform a supervisory reset by entering [*][8][Installer's Code][902]. The

You should mount the keypad where it is accessible to designated points of entry and exit. Once you have

panel will now supervise all assigned keypads and enrolled modules on the system.

selected a dry and secure location, perform the following steps to mount the keypad.

1. Remove the keypad backplate by loosening the screw (optional) located at the base of the unit.

Programming the Keypad

There are several programming options available for the LCD5511

2. Secure the keypad backplate to the wall in the desired location. Use the screws provided.

keypad. These are described below. Record all your programming

3. To use the keypad tamper, insert the tamper switch supplied into the opening located in the centre of

choices in the programming worksheets included in this manual.

the backplate.

4. For tamper use, try to ensure the backplate is mounted on a smooth, flat surface. If mounting on a

Programming the LCD5511 is similar to programming the rest of

the system. When you are in the LCD5511 programming sections,

rough surface, fasten the enclosed surface tape to the wall to even out the surface area where the

tamper will be positioned.

the keypad will display which options are turned on along the top of the display. To turn an option on or

off, press the number corresponding to the option on the number pad. The numbers of the options that

5. Before attaching the keypad to its backplate, complete the keypad wiring as described in the next sec-

are currently turned ON will be displayed. For example, if options 1 and 2 are on, see above. For infor-

tion.

mation on programming the rest of your security system, please refer to your system Installation Manual.

Wiring

Function Key Options

1. Before wiring the unit, ensure that all power (AC transformer and battery) is disconnected from the

control panel.

The function keys are programed in sections [000][1-4]. By default, the 4 function keys on the keypad

are programmed as Stay Arm (03), Away Arm (04), Chime (06), Aux (11). You can change the function

2. Connect the four Keybus wires from the control panel (red, black, yellow and green) to the keypad ter-

minals (R B Y G). Consult the diagram below:

of each key on every keypad. Please see your system's Installation Manual for instructions on program-

ming the keys, and a complete list of all the function key options available for your system.

3. If programmed as an input, you can connect a device - such as a

Clock Options

door contact - to the 'Z/P' terminal of the LCD5511. This elimi-

LCD

5511

The LCD5511 will display the current time after 4 seconds of no key presses. To set the correct time and

nates the need to run wires back to the control panel for the device.

date for the system, please refer to your system's Instruction Manual. You can change how the keypad

To connect the zone, run one wire from the device to the 'Z/P' ter-

displays the time with the following options. To change the clock options:

minal and the other wire from the device to the B (black) terminal.

B Y G Z/P

1. Enter [*][8][Installer's code]

For powered devices, run the red wire to the R (positive) terminal

and the black wire to the B (negative) terminal. When using end of

2. Enter [000] to go to keypad programming

3. Enter section [6] to go to clock options.

line supervision, connect the zone according to one of the configu-

To Zone Input/

RED BLK YEL GRN

4. To turn any of the options on or off, press [1], [2], or [3]:

rations outlined in your system's Installation Manual.

PGM Output

NOTE: If the Time does not display on keypad option is selected, make sure that the Keypad

[6] ON = Door Chime Enabled for Zone Openings

displays time when zones are open option is also selected.

OFF = Door Chime Disabled for Zone Openings

[1] ON = Time displays on keypad

[7] ON = Door Chime Enabled for Zone Closings

OFF = Time does not display on keypad

OFF = Door Chime Disabled for Zone Closings

[2] ON = Clock display is in 12-hour format (e.g. 08:00).

5. When you are finished, press [#] to exit.

OFF = Clock display is in 24-hour format (e.g. 20:00)

Door Chime Sounds

[3] ON = Keypad does not display time when zones are open

You can program the LCD5511 keypad to make different door chime sounds for individual zones, or

groups of zones. Each LCD5511 keypad can make any of four door chime sounds for each zone that trig-

OFF = Keypad displays time when zones are open

gers the door chime:

5. When you are finished programming the clock options, press [#] to exit.

• 4 quick beeps (default sound)

Alarms Displayed While Armed Option

• 'Bing – Bing' tone

You can disable the display of alarms on the keypad when the system is armed. The display of alarms is

NOTE: For a zone to be able to trigger the door chime sound, the Door Chime zone attribute

enabled by default. To disable the display of alarms when the system is armed, turn off section [6],

must also be enabled in the control panel programming. Please see your control panel

option [5]:

Installation Manual.

1. Enter [*][8][Installer's code]

To change the door chime sounds:

2. Enter [000] to go to keypad programming

1. Enter [*][8][Installer's code].

3. To turn the display of alarms on or off, enter section [6].

2. Enter [*] to go to door chime sound programming.

4. Turn option [5] on or off:

3. Enter a 2-digit number for the zone you want to program [01] - [64].

[5] ON = Alarms not displayed while system is armed

4. Turn one of the following options on by pressing [1], [2], [3], or [4]:

OFF = Alarms are always displayed while system is armed

[1] 4 quick beeps (default sound)

5. When you are finished, press [#] to exit.

[2] 'Bing – Bing' tone

Emergency Key Options (Fire, Auxiliary, Panic)

[3] 'Ding – Dong' tone

You can enable or disable the Fire, Auxiliary and Panic keys at each keypad. These keys are enabled by

[4] 'Alarm' tone

default. Please see your system's Installation Manual for more information on these keys and their

NOTE: Make sure that only one of the above options is turned on. If more than one is on, the

options. To turn any of the emergency keys on or off on the keypad:

keypad will sound the first option that is enabled. If none of the options are selected, the key-

1. Enter [*][8][Installer's code]

pad will not make any sound when the zone is opened or closed.

2. Enter [000] to go to keypad programming

5. To program the door chime sound for another zone, repeat steps 3 and 4.

3. Enter section [7].

6. When you are finished programming the door chime sounds, press [#] to exit.

4. To turn the emergency key options on or off, press [1], [2], or [3]:

[1] ON=Fire key enabled

OFF=Fire key disabled

Zone Input/PGM Output Option

[2] ON=Auxiliary key enabled

OFF=Auxiliary key disabled

The LCD5511 'Z/P' terminal can be programmed to support one zone input (default) or one PGM output.

To change this option:

[3] ON=Panic key enabled

OFF=Panic key disabled

1. Enter [*][8] [Installer Code].

5. When complete, press [#] to exit.

2. Enter [000] to go to keypad programming.

Door Chime Options

3. Enter section [6].

You can program the LCD5511 keypad to sound a tone when any zone is opened or closed. There are two

4. Turn the option on or off by pressing [8].

parts to the LCD5511 door chime programming:

If Option 8 is ON, the 'Z/P' terminal is an output.

• Program if the LCD5511 will chime when zones are opened and/or closed.

If Option 8 is OFF, the 'Z/P' terminal is an input.

• Program the type of sound the LCD5511 will make when an individual zone is opened or

Programming the PGM Number

closed.

In order to assign a PGM output to the "Z/P" terminal, a PGM number must be entered. This number has

For the door chime feature to work, you will also need to turn on the Door Chime attribute for each zone

to be one of the PGM outputs that can be programmed in the panel.

that will trigger the chime. This programming is done in the control panel software. Refer to your control

1. Enter [*][8] [Installer Code].

panel's Installation Manual for more information.

2. Enter [000] to go to Keypad Programming.

Door Chime on Zone Openings/Closings

3. Enter Section [8].

You can program each LCD5511 keypad to sound a door chime when zones are opened and/or when

4. Enter the 2-digit PGM number (01-14).

they are closed. By default, LCD5511 keypads are programmed to sound door chimes on both zone

AC Icon (PC5020/PC1616/1832/1864 only)

openings and closings.

The AC icon displays the AC is present at the main panel. You can program the LCD5511 to either go out

To change the door chime opening/closing settings, at each LCD5511 keypad:

or flash when the AC is not present.

1. Enter [*][8][Installer's Code]

1. Enter [*][8] [Installer Code]

2. Enter [000] to go to keypad programming

2. Enter [000] to go to Keypad Programming.

3. Enter section [6].

3. To select the desired operation for the AC icon, enter section [6].

4. To turn the options on or off, press [6] or [7]:

4. Turn Option [4] On or Off:

ON = AC Icon flash on loss of power

OFF= AC icon not displayed on loss of power

5. When you are finished, press [#] to exit.

Trouble Icon

The Trouble icon is displayed when a system trouble is active.

Low Temperature Warning

The keypad zone can be alternatively programmed to be a low temperature warning instead of a physical

zone input. If programmed, the zone will go into alarm at 6°C (+/-2°) and restore at 9°C (+/-2°).

• 'Ding – Dong' tone

1. Enter [*][8] [Installer Code].

• 'Alarm' tone

2. Enter [000] to go to Keypad Programming.

3. Enter section [7].

4. Enable or disable the low temperature warning by pressing [8].

ON = Low temperature warning enabled

OFF = Low temperature warning disabled

Only 1 of 3 options may be selected for the input/output terminal (Zone, PGM or Low

Temperature).

IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is

copyrighted and is purchased under the following license terms:

• This End-User License Agreement ("EULA") is a legal agreement between You (the company, individual

or entity who acquired the Software and any related Hardware) and Digital Security Controls, a division of

Tyco Safety Products Canada Ltd. ("DSC"), the manufacturer of the integrated security systems and the

developer of the software and any related products or components ("HARDWARE") which You acquired.

• If the DSC software product ("SOFTWARE PRODUCT" or "SOFTWARE") is intended to be accompanied

by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the

SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include asso-

ciated media, printed materials, and "online" or electronic documentation.

• Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user

license agreement is licensed to You under the terms of that license agreement.

• By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT,

You agree unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a

modification of any previous arrangement or contract. If You do not agree to the terms of this EULA, DSC

is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.

SOFTWARE PRODUCT LICENSE

The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as

other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.

1. GRANT OF LICENSE This EULA grants You the following rights:

(a) Software Installation and Use - For each license You acquire, You may have only one copy of the

SOFTWARE PRODUCT installed.

(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run,

shared or used concurrently on or from different computers, including a workstation, terminal or other

digital electronic device ("Device"). In other words, if You have several workstations, You will have to

acquire a license for each workstation where the SOFTWARE will be used.

one copy per license installed at any given time. You may use the back-up copy solely for archival

purposes. Except as expressly provided in this EULA, You may not otherwise make copies of the

SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS

(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer,

decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity

is expressly permitted by applicable law notwithstanding this limitation. You may not make any

changes or modifications to the Software, without the written permission of an officer of DSC. You may

not remove any proprietary notices, marks or labels from the Software Product. You shall institute

reasonable measures to ensure compliance with the terms and conditions of this EULA.

(b) Separation of Components -

The SOFTWARE PRODUCT is licensed as a single product. Its

component parts may not be separated for use on more than one HARDWARE unit.

If You acquired this SOFTWARE with HARDWARE, then the

SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product. In this case, the

SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA..

(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to

others or post it on a server or web site.

(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a

permanent sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the

SOFTWARE PRODUCT (including all component parts, the media and printed materials, any upgrades

and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE

PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE

PRODUCT.

(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply

with the terms and conditions of this EULA. In such event, You must destroy all copies of the

SOFTWARE PRODUCT and all of its component parts.

(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service

marks of DSC or its suppliers.

3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but

not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the

accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its

suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and

intellectual property rights in and to the content which may be accessed through use of the SOFTWARE

PRODUCT are the property of the respective content owner and may be protected by applicable copyright or

other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights

not expressly granted under this EULA are reserved by DSC and its suppliers.

4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to

any country, person, or entity subject to Canadian export restrictions.

5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario,

Canada.

6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and

binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the

arbitrator's decision. The place of arbitration shall be Toronto, Canada, and the language of the arbitration

shall be English.

7. LIMITED WARRANTY

(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE "AS IS" WITHOUT WARRANTY. DSC DOES NOT

WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE

SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.

(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by

changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the

SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.

STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC'S

ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE

GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE

CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY

NOT APPLY TO YOU.

(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE

IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL

OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC

NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO

MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY

CONCERNING THIS SOFTWARE PRODUCT.

NOTE: (e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL

DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON

BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL

THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFT-

WARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR

REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF

THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that

the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but

not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail

to perform as expected.