DSC PowerSeries PC1616 Kurulum Kılavuzu - Sayfa 4

Güvenlik Sistemi DSC PowerSeries PC1616 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. DSC PowerSeries PC1616 17 sayfaları. System enhancement module
Ayrıca DSC PowerSeries PC1616 için: Kurulum Kılavuzu (13 sayfalar), Hızlı Kılavuz (4 sayfalar), Kurulum Kılavuzu (20 sayfalar), Manuel (18 sayfalar)

Sayfayı Yazdır

4. AUX Power Wiring

The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LED's etc.... If the total current

required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below.

NOTE: Min/max operating voltages for devices, sensors and modules is 9.5V

Refer to the list of Compatible Devices on the first page for the current draw of individual devices

5. PGM Wiring

PGMs switch to ground when activated by control panel.

Connect the positive side of the device to be activated to the AUX+

Terminal. Connect the negative terminal to the PGM.

current output is as follows

•

PGM 1, 3, 4 .................... 50mA

•

PGM 2 .......................... 300mA

For currents levels greater than 300mA a relay is required.

PGM2 can also be used for 2-wire smoke detectors.

NOTE: Use SEOL resistors on Fire Zones ONLY.

2-wire Smoke Detectors Initiating Circuit

•

Style B (Class B), Supervised, Power Limited

•

Compatibility Identifier ........................................................ PC18-1

•

DC Output Voltage..................................................... 9.8-13.8 VDC

•

Detector Load ............................................................. 2 mA (MAX)

•

Single-end-of-line (SEOL) Resistor ..................................... 2200Ω

•

Loop Resistance............................................................24Ω (MAX)

Standby Impedance.................................................. 1020Ω (ΝΟΜ)

•

Alarm Impedance ........................................................570Ω (MAX)

•

Alarm Current ............................................................ 89 mA (MAX)

Compatibility ID For FSA-210B Series is: FS200

6. Telephone Line Wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an

RJ-31x Connector as indicated.

For connection of multiple devices to the telephone line, wire in the

sequence indicated.

Telephone format is programmed in section [350].

Telephone Call Directions are programmed in section [351]-[376].

7. Ground

Ground Installation

Tighten nut to break paint and make

good connection to the cabinet

Hardware Installation (Cont.)

8. Battery

A sealed, rechargeable, lead

acid battery or gel type battery is

required to meet UL require-

ments for power standby times.

NOTE: UL Residential/Commer-

cial Burglary installations require

4Hrs Power Standby time.

NOTE: UL/ULC Residential Fire

& Home Care installations

require 24 Hr power standby.

ULC Commercial Burglary

and Fire monitoring installations

require 24 Hr power standby.

PGM 1, LED Output with current limiting resistor and Optional Relay

driver output

4-wire Smoke Detectors

RM-1/RM-2 POWER LOOP

SUPERVISORY RELAY

T-1

R-1

TIP

RING

Standby Battery Guide

Battery Charging Current: 400 mA

Batt

Standby

Size

4Hr

24Hr

-------------------------------------------------

4Ahr

700mA

----

7Ahr

700mA

180mA

14Ahr

700mA

470mA

NOTE:

Replace batteries every 3-5 years.

Battery capacity will deteriorate with

age and number of charge/discharge

cycles

- 14V

RJ-31X

9. AC Wiring

AC Wiring

UL Listed Installations

Primary: 120VAC/60Hz./0.33A

Secondary: 16.5VAC/40VA

DSCPTD 1640 Plug-in, Class 2

Transformer.

NOTE: Do not connect trans-

former to a receptacle controlled

by a switch. (UL Listed Installations

Only)