DSC PowerSeries PC1832 Kurulum Kılavuzu - Sayfa 16

Güvenlik Sistemi DSC PowerSeries PC1832 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. DSC PowerSeries PC1832 17 sayfaları. System enhancement module
Ayrıca DSC PowerSeries PC1832 için: Kurulum Kılavuzu (13 sayfalar), Kurulum Kılavuzu (20 sayfalar), Manuel (18 sayfalar)

DSC PowerSeries PC1832 Kurulum Kılavuzu

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void
your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television re-
ception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Re-orient the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to Identify and Resolve
Radio/Television Interference Problems". This booklet is available from the U.S. Government Print-
ing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that
contains, among other information, the FCC registration number and ringer equivalence number
(REN) for this equipment. If requested, this number must be provided to the Telephone Company.
PC1864 Product Identifier
PC1832 Product Identifier
PC1616 Product Identifier
REN:
USOC Jack:
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line. Exces-
sive RENs on a telephone line may result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local Telephone
Company. For products approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format.
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is
a REN of 0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm
If this equipment PC1864/PC1832/PC1616 causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of service may be required. But
if advance notice is not practical, the Telephone Company will notify the customer as soon as possi-
ble. Also, you will be advised of your right to file a complaint with the FCC if you believe it is nec-
essary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the Telephone Company will provide
advance notice in order for you to make necessary modifications to maintain uninterrupted service.
© 2006, Digital Security Controls
Printed in Canada
US: F53AL01BPC1864
US: F53AL01BPC1832
US: F53AL01BPC1614
0.1B
RJ-31X
Equipment Maintenance Facility
If trouble is experienced with this equipment PC1616, PC1832, PC1864 for repair or warranty infor-
mation, please contact the facility indicated below. If the equipment is causing harm to the telephone
network, the Telephone Company may request that you disconnect the equipment until the problem
is solved. This equipment is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility commission,
public service commission or corporation commission for information.
Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency
situation. It must be able to do this even if other equipment (telephone, answering system, computer
modem, etc.) already has the telephone line in use. To do so, alarm dialling equipment must be con-
nected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other
equipment attached to the same telephone line. Proper installation is depicted in the figure below. If
you have any questions concerning these instructions, you should consult your telephone company
or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.
Customer Premises Equipment and Wiring
Network
Service
Provider's
RJ-31X
Facilities
Jack
Alarm Dialing
Telephone
Line
Network
Demarcation
Point
Telephone
Answering
System

INDUSTRY CANADA STATEMENT

NOTICE: This Equipment meets the applicable Industry Canada Terminal Equipment Technical Spec-
ifications. This is confirmed by the registration number. The abbreviation, IC, before the registration
number signifies that registration was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that that Industry Canada approved
the equipment
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN as-
signed to each terminal equipment provides an indication of the maximum number of terminals allowed
to be connected to a telephone interface. The termination on an interface may consist of any combina-
tion of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all
devices does not exceed five.
PC1864 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . .IC: 160A-PC1864
PC1832 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . .IC: 160A-PC1832
PC1616 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . .IC: 160A-PC1614
Computer
Unused
RJ-11 Jack
Equipment
Unused
Fax Machine
RJ-11 Jack
Telephone
Telephone