Absolute Process Instruments API 6380 G D Hızlı Başlangıç Kılavuzu - Sayfa 2

Verici Absolute Process Instruments API 6380 G D için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Absolute Process Instruments API 6380 G D 2 sayfaları. Ac to dc transmitters, isolated, field rangeable

Sayfayı Yazdır

Absolute Process Instruments API 6380 G D Hızlı Başlangıç Kılavuzu

Installation and Setup

Precautions

WARNING! All wiring must be performed by a qualified electrician or

instrumentation engineer. See diagram for terminal designations and

wiring examples. Consult factory for assistance.

WARNING! Avoid shock hazards! Turn signal input, output, and

power off before connecting or disconnecting wiring, or removing

or installing module.

Précautions

ATTENTION! Tout le câblage doit être effectué par un électricien

ou ingénieur en instrumentation qualifié. Voir le diagramme pour

désignations des bornes et des exemples de câblage. Consulter

l'usine pour assistance.

ATTENTION! Éviter les risques de choc! Fermez le signal d'entrée,

le signal de sortie et l'alimentation électrique avant de connecter

ou de déconnecter le câblage, ou de retirer ou d'installer le module.

API maintains a constant effort to upgrade and improve its products.

Specifications are subject to change without notice. See api-usa.com for

latest product information. Consult factory for your specific requirements.

WARNING: This product can expose you to chemicals includ-

ing lead and nickel, which are known to the State of California

to cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

Socket and Mounting

Install module in a protective panel or enclosure. Allow space around

module for air flow. Use API 008 or API 008 FS socket. See specifica-

tions for maximum allowable socket voltages. The socket clips to a

standard 35 mm DIN rail or can be mounted to a flat surface.

Output Reversal Configuration

The default configuration is normal acting output. The output can be

reversed by moving an internal jumper.

1. Unplug the module from the socket.

2. Remove 4 screws from the module bottom and lift off plastic case.

3. Note location of circuit board jumper. See diagram below.

4. Place jumper as indicated for desired output operation.

5. Replace cover and screws.

transformer

jumper

Normal Output

Range Selection

Set I/O ranges before plugging the module in. See the model/serial

number label for options or if a custom range was specified. See

module label for common ranges or table below to select I/O ranges.

Switch A: Set to "V" for voltage output or "I" for current output.

Switch B: Output range

Switch C: Input range

Switch D: Input range

Switch E: Set to "V" for voltage input or "I" for current input.

Switch E determines the input impedance for the module, typically

10 Ω for current inputs and 220 kΩ or 1 MΩ for voltage inputs.

Output

0-1 V

0-2 V

Switches

ABCDE

Input t

0-5 mA

V0A2I

V8A2I

V1A2I

0-10 mA

V022I

V822I

V122I

0-50 mA

V002I

V802I

V102I

0-100 mA

V092I

V892I

V192I

V012I

V812I

V112I

0-200 mA

0-50 mV

V0A2V

V8A2V

V1A2V

0-100 mV

V022V

V822V

V122V

0-200 mV

V0B2V

V8B2V

V1B2V

0-500 mV

V002V

V802V

V102V

0-1 V

V092V

V892V

V192V

0-2 V

V012V

V812V

V112V

0-5 V

V000V

V800V

V100V

0-10 V

V062V

V862V

V162V

0-20 V

V0F2V

V8F2V

V1F2V

0-50 V

V042V

V842V

V142V

0-100 V

V0D2V

V8D2V

V1D2V

0-125 V

V049V

V849V

V149V

V054V

V854V

V154V

0-175 V

0-200 V

V052V

V852V

V152V

0-250 V

V0D9V

V8D9V

V1D9V

BSOLUTE

ROCESS

Signal Output

Polarity must be observed when connecting the signal output to the

load. The module provides 20 VDC power to the output loop when

current output is selected.

Signal Input

For safety, input must be off while connecting wiring. Input voltages

must not exceed socket voltage rating. Connect the AC signal input

to terminals 5 and 6.

Module Power

Check model/serial number label for module operating voltage to

make sure it matches available power.

AC power is connected to terminals 1 and 3.

For DC powered modules, polarity MUST be observed.

Positive (+) is wired to terminal 1

Negative (–) is wired to terminal 3

Calibration

Input and output ranges, if specified on your order, are factory pre-

configured (at 24°C ±1°C). The Zero and Span potentiometers can be

used fine-tune the output range.

Note: Perform the following calibration procedure any time switch

settings are changed.

1. Power the module and allow a minimum 20 minute warm up time.

2. Using an accurate calibration source, provide an input to the

module equal to the minimum input required for the application.

transformer

3. Using an accurate measurement device for the output, adjust the

Zero potentiometer for the exact minimum output desired. The Zero

control should only be adjusted when the input signal is at its mini-

mum. This will produce the corresponding minimum output signal.

Reverse Output

For example: 4 mA for a 4-20 mA output or –10 V for a ±10V

output.

4. Set the input at maximum, and adjust the Span pot for the exact

maximum output desired. The Span pot should only be adjusted

when the input signal is at its maximum. This will produce the

corresponding maximum output signal.

5. Repeat adjustments for maximum accuracy.

Test Range Adjust – Turn the multi-turn Test Range potentiometer

while holding the Test button depressed until the desired output test

level is reached. It can be adjusted to vary the output signal from 0

to 100% of the output range.

0-4 V

1-5 V

0-5 V

0-8 V

ABCDE

V6A2I

V9A2I

V2A2I

V622I

V922I

V222I

V602I

V902I

V202I

V692I

V992I

V292I

V612I

V912I

V212I

V6A2V

V9A2V

V2A2V

V622V

V922V

V222V

V6B2V

V9B2V

V2B2V

V602V

V902V

V202V

V692V

V992V

V292V

V612V

V912V

V212V

V600V

V900V

V200V

V662V

V962V

V262V

V6F2V

V9F2V

V2F2V

V642V

V942V

V242V

V6D2V

V9D2V

V2D2V

V649V

V949V

V249V

V654V

V954V

V254V

V652V

V952V

V252V

V6D9V

V9D9V

V2D9V

NSTRUMENTS

6380 G

Output

Input

Output

Input

Sel.

Range

Range 1

Range 2

2-10 V

0-10 V

±5 V

±10 V

ABCDE

V7A2I

V3A2I

V4A2I

V5A2I

V722I

V322I

V422I

V522I

V702I

V302I

V402I

V502I

V792I

V392I

V492I

V592I

V712I

V312I

V412I

V512I

V7A2V

V3A2V

V4A2V

V5A2V

V722V

V322V

V422V

V522V

V7B2V

V3B2V

V4B2V

V5B2V

V702V

V302V

V402V

V502V

V792V

V392V

V492V

V592V

V712V

V312V

V412V

V512V

V700V

V300V

V400V

V500V

V762V

V362V

V462V

V562V

V7F2V

V3F2V

V4F2V

V5F2V

V742V

V342V

V442V

V542V

V7D2V

V3D2V

V4D2V

V5D2V

V749V

V349V

V449V

V549V

V754V

V354V

V454V

V554V

V752V

V352V

V452V

V552V

V7D9V

V3D9V

V4D9V

V5D9V

1220 American Way Libertyville, IL 60048

Phone:

800-942-0315

API 6380 G Series

Operation

Depending on the rotary switch settings, the input is either ampli-

fied or attenuated, then filtered and processed by a precision full-

wave rectification circuit. The result is passed thru a low pass active

filter that provides a DC voltage representing the average value of

the input. This DC voltage is passed through an optical isolation

circuit to the output stage.

Test Button – Drives a device on the output side of the loop (a

panel meter, chart recorder, etc.) with a known good signal that can

be used as a system diagnostic aid during initial start-up or during

troubleshooting. When released, the output will return to normal.

GREEN LoopTracker

Input LED – Provides a visual indication that

a signal is being sensed by the input circuitry of the module. It also

indicates the input signal strength by changing in intensity as the

process changes from minimum to maximum. If the LED fails to illu-

minate, or fails to change in intensity as the process changes, this

may indicate a problem with module power or signal input wiring.

RED LoopTracker output LED – Provides a visual indication that the

output signal is functioning. It becomes brighter as the input and the

corresponding output change from minimum to maximum. For cur-

rent outputs, the LED will only light if the output loop current path is

complete. For either current or voltage outputs, failure to illuminate or

a failure to change in intensity as the process changes may indicate

a problem with the module power or signal output wiring.

AC voltage or

AC mA input

Socket top

view

Key down

when

panel

mounting

mA output

(+)

(–)

20 V sourcing

Device

w. mA

Input

Voltage

output

(+)

(–)

Device

w. Voltage

Input

0-2 mA

2-10 mA 0-10 mA 0-16 mA 4-20 mA 0-20 mA

ABCDE

I0A2I

I6A2I

I9A2I

I2A2I

I022I

I622I

I922I

I222I

I002I

I602I

I902I

I202I

I092I

I692I

I992I

I292I

I012I

I612I

I912I

I212I

I0A2V

I6A2V

I9A2V

I2A2V

I022V

I622V

I922V

I222V

I0B2V

I6B2V

I9B2V

I2B2V

I002V

I602V

I902V

I202V

I092V

I692V

I992V

I292V

I012V

I612V

I912V

I212V

I000V

I600V

I900V

I200V

I062V

I662V

I962V

I262V

I0F2V

I6F2V

I9F2V

I2F2V

I042V

I642V

I942V

I242V

I0D2V

I6D2V

I9D2V

I2D2V

I049V

I649V

I949V

I249V

I054V

I654V

I954V

I254V

I052V

I652V

I952V

I252V

I0D9V

I6D9V

I9D9V

I2D9V

api-usa.com

Fax: 800-949-7502

AC or DC (–)

Module power

AC or DC

(+)

 * Do not make

connections to

unused terminals!

To maintain full isola-

tion avoid combining

power supplies in

common with input,

output, or unit power.

ABCDE

I7A2I

I3A2I

I722I

I322I

I702I

I302I

I792I

I392I

I712I

I312I

I7A2V

I3A2V

I722V

I322V

I7B2V

I3B2V

I702V

I302V

I792V

I392V

I712V

I312V

I700V

I300V

I762V

I362V

I7F2V

I3F2V

I742V

I342V

I7D2V

I3D2V

I749V

I349V

I754V

I354V

I752V

I352V

I7D9V

I3D9V