DT Research SA101 Temel Kullanım Kılavuzu - Sayfa 2

Dijital Tabela DT Research SA101 için çevrimiçi göz atın veya pdf Temel Kullanım Kılavuzu indirin. DT Research SA101 2 sayfaları. Signage appliance

Sayfayı Yazdır

I/O Port

Precautions

•

Always exercise care when operating and handling.

•

Never disassemble any portion of the enclosure, as this will void any product warranty.

•

Do not use any AC/DC adapter other than the one provided with the device or acquired from

the manufacturer or its partners.

•

In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately

power down the product and disconnect all power sources.

•

Please report the problem to your device provider immediately.

•

Pushing on the Power Button again will restart the appliance.

Powering ON and OFF

The SA101 is programmed to Power On automatically when power is ﬁrst applied or

reestablished. There is also a Power Button, located on the front of the SA101. To turn the SA101

on, push and release the Power Button on the front bezel. The adjacent power LED will be lit

(blue), and the corresponding interface will be shown on the display monitor. To turn oﬀ the

device, use the software shutdown interface provided. In the event of system lockup, unplug or

re-plug the power cable. Also, the Power Button may be used to perform a reset of the device.

To do that, push and hold the Power Button for at least 2 seconds, then the rebooting/shutting

down message will be shown.

Server Installation

Please refer to the corresponding User Guides for software installation instructions.

Connect Player and Register to WCM Server

•

After powering on your signage player, the registration dialog will be launched automatically.

•

In case the registration dialog is not automatically initiated, you may select and launch the

DTPlayer application on the Application screen.

•

If you want to register the Player to another WCM server, right click the mouse and then

select Register Player Again on the dialog box.

•

Please refer to documentation included in the DVD of your package to start

content, playlists and schedules via WebDT Content Manager.

NOTE: If your signage player is located in a LAN with a WCM server, the player will automatically

ENGLISH

USB 1.1/2.0

(If the mouse/keyboard only supports

USB 1.1, connect to this port)

USB 2.0

HDMI 2.0

1920 x 1080 @ 60Hz

3840 x 2160 @ 60Hz*

(*RGB 4:4:4, YCbCr 4:4:4 and YCbCr 4:2:2)

managing your

Registration Information:

Player name: Leave default name or give a new name

Group name: If you did not create a group in WCM server yet, leave it blank now

Organization name: my site (default)

Access Password: 123456 (default)

Publish Server URL:http://(server IP address): (port number)/publish

or, http://localhost: (Port number)/publish

NOTE: While there is an external storage device (HDD, USB stick, SD card, etc.) with storage

capacity larger than of the internal storage connected to the SA101, you may select "Select the

external storage device with largest capacity as media library path" for storing the downloaded

content. However, if the external storage capacity is less than the internal, you can only save the

downloaded content in the internal storage.

VESA Mounting Bracket Installation Guide for SA101

The DT Research Signage Appliance package includes a VESA-compliant mounting bracket (1)

which mounts the SA101 (2) onto a VESA-compatible monitor or display.

NOTE: The VESA Mounting Bracket is compatible with most displays and monitors that support

the VESA standard.

Step1:

•

Locate the existing mounting holes on the monitor.

•

Line the bracket holes up with the holes on the back of the monitor,

as pictured.

•

Place the screws to hold the mounting bracket in place and tighten

the screws (do not over-tighten).

Step2:

•

Remove the two M3 screws (3) originally on the SA101 signage

appliance.

•

Place the SA101 (2) on the bracket rail with the interface ports side

facing downwards so that the two mounting holes on the appliance

are aligned with the existing holes on the rail (see picture).

Step 3:

•

Apply and tighten the screws into their original locations and make sure

that the bracket and the SA101 are properly secured.

<1>

<2> <3>

ENGLISH