Attwood 5550 Series Kurulum Talimatları

Deniz Aydınlatma Attwood 5550 Series için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Attwood 5550 Series 2 sayfaları. Attwood navigation light installation instructions led anti-glare fold-down and fixed base lights

Sayfayı Yazdır

All-Round Light

5550 Series LED Anti-Glare Fold-Down

and Fixed Base Lights

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69428 Rev. A

Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards

as tested by Immana Labs, 5/3/07. 2 Nautical Mile visibility.

CAUTION: Read all instructions carefully before installing and using this product. All positive

(+12V DC) lighting wires require a 1-amp fuse to protect circuits and vessel. The aluminum

light pole is not grounded. MAKE SURE POWER SOURCE IS 12-VOLT DC ONLY. HIGHER

VOLTAGE WILL DAMAGE LIGHT AND CIRCUITRY.

WARNING

To prevent injury, disconnect power when installing or servicing this product. Remove

boat from water before using 120V power tools.

REQUIRED FOR INSTALLATION

• Cordless drill; 1/8" and 3/8" (3 and 10mm) bits

• Marine-grade non-silicone sealant

• Phillips screwdriver

• Two #10 pan head stainless steel screws

• 3-position switch (OFF/ON/ON)

• Fuse holder and fuse: 1-amp

• 16-gauge wire

• Appropriate marine-grade wire connectors

LED Anti-Glare All-Round Lights are designed for boats up to 39.4 feet (12m). It provides

360 degree controlled light output and 2-mile visibility while shielding the driver from

on-board glare (Figure 1). Position the All-Round Light so its bulb is not less than one

meter (39.4") above sidelights. If replacing an existing pole light, replace with a pole at

least as long as the existing pole.

Mount the anti-glare light in a position so that:

• Light output is ﬂ at and parallel to water when boat is ﬂ oating.

• Light shines 360°, unobstructed.

• Light does not shine on operator, or reﬂ ect off any part of the boat in the operator's

ﬁ eld of vision.

Figure 1

Figura 1

One meter

39 3/8 po

39-3/8"

or 39-3/8"

(un mètre)

(un metro)

INSTALLATION INSTRUCTIONS

Bases are available for mounting on vertical or horizontal surfaces. Release the cam-lock

adjustment handle to fold light or adjust to vertical position.

Change Base Type (If Required) on Fold-Down Base

Packaged versions of the light are shipped with the horizontal base installed. To switch

to the vertical base:

1. Carefully remove the cam-lock screw and oblong washer. Set aside for reinstallation

(Figure 2).

Figure 2

Figura 2

STEP 1

STEP 2

ÉTAPE 1

ÉTAPE 2

PASO 1

PASO 2

Horizontal Base

Cam-lock Screw

Base horizontale

and Oblong Washer

Base horizontal

Vis de serrage et

rondelle oblongue

Tornillo con leva de

fijación y arandela alargada

07-10

STEP 3

ÉTAPE 3

Socket

PASO 3

Douille

Portalámparas

Axle

Axe

Eje

Vertical Base

Base verticale

Base vertical

Feed Wires Thru

Insérez les fils à travers

Pasar los cables

2. Pivot the base axle out of its socket. Note position of the 2 wires in the base slot.

Remove the horizontal base.

3. Insert wires through slot of the vertical base. Reassemble in reverse order.

Mark Position for Fixed Base Light, (Figure 3)

1. Place light in selected position.

2. Using the base as a template, mark the two mounting hole locations and one wire

access hole. Proceed to "Install Light" below.

Figure 3

Figura 3

Mark Position for Fold-Down Light

1. Release cam-lock adjustment handle and adjust light to vertical position. (Figure 4)

2. Place light in selected position.

3. Use optional adaptors, if necessary, to allow installation on angled windshields.

4. Using the base as a template, mark the two mounting hole locations and one wire

access hole. (Figure 5) Proceed to "Install Light" below.

Figure 4

Figura 4

Horizontal Mount

Montage horizontal

Montaje horizontal

Figure 5

Figura 5

Vertical Mount

Montage vertical

Montaje vertical

Install Light

CAUTION: Position wire access hole carefully, especially on aluminum boats, so that

wires do not contact the hull.

1. Remove light from marked position. Drill two 1/8" (3mm) pilot holes for #10 screws.

Drill one 3/8" (10mm) wire access hole.

2. Bring the two 16-gauge wires up through access hole.

3. Use marine-grade waterproof crimp connectors to connect gray wire to positive

lead from 3-position switch. Connect (-) negative source to black wire and route

to (-) negative terminal on battery.

4. Fasten light to deck with two #10 stainless steel pan head screws. DO NOT OVERTIGHTEN.

Base Wiring

IMPORTANT: LED-based lights MUST be wired for correct polarity.

NOTE: Do not use light pole as a ﬂ agpole or handle.

OPERATION

After installation, check lights to verify proper operation. Regulations require lights to

be operated with a three-position switch for:

1. Running lights (sidelights and all-round light);

2. Anchor lights (all-round light only);

3. Off.

ATTWOOD LIMITED 10-YEAR WARRANTY

Because of the longevity of Attwood's LED lighting technology, Attwood offers a limited

10-year warranty on this LED lighting product. See Product Catalog or attwoodmarine.com

for details.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Locked

Verrouillé

Trabado

Optional

Unlocked

Adaptor

Déverrouillé

Adaptateur

Destrabado

en option

Adaptador

opcional