AdDent Compex HD Kullanım Talimatları - Sayfa 2

Dişçilik ekipmanları AdDent Compex HD için çevrimiçi göz atın veya pdf Kullanım Talimatları indirin. AdDent Compex HD 2 sayfaları. Heated dispenser

Sayfayı Yazdır

CHARGING THE UNIT

Note: The Compex HD unit should be fully charged prior to first time use.

A wall plug-in USB power supply is provided to charge the unit. The power

supply operates from wall Voltages from 100 to 240 Volts, AC. Connect the

USB cord to the power supply and plug the power supply into a suitable wall

outlet. Plug the opposite end of the USB cord into the connector located on

the bottom of the Compex HD handle.

Do not attempt to use the Compex HD when the unit is

charging. The unit cannot be activated while the power supply

is connected to the unit.

BATTERY CHARGE INDICATOR

Charging the Compex HD: While charging the unit, the right side

LED battery charge indicator blinks red. When the unit is fully

charged, the LED turns solid green.

Operating the Compex HD: While using the unit, the right side LED battery

charge indicator operates as follows:

GREEN - Battery is charged, normal operation.

AMBER - Battery charge at approximately 20%, unit has 10 minutes of

useful charge remaining.

RED - Battery is at the end of useful charge and requires recharging.

TEMPERATURE STATUS INDICATOR

The LED on the left side indicates the temperature status. For the

first minute of the heating cycle the temperature status LED blinks

AMBER. At one minute the LED starts blinking GREEN. At two

minutes the LED turns solid GREEN. The LED stays solid GREEN for the

remaining eight minutes of the heating cycle.

INSTALLING THE COMPULE (PLT)

1. Place the compule into the opening in the barrel ensuring that the

compule flange is positioned as far back as possible.

2. Press the compule into the compule holder with firm even pressure. The

compule will snap into place.

3. Ensure that the compule body is fully seated against the compule holder

with the compule flange as far back as possible.

OPERATION – HEATING AND DISPENSING COMPULES

• The heating cycle warms the composite to 155°F (68°C): Pressing the

on/off button once activates the heating cycle. For the first minute of the

heating cycle the temperature status LED blinks AMBER. At one minute the

LED starts blinking GREEN. At two minutes the LED turns solid GREEN.

The LED stays solid GREEN for the remaining eight minutes of the heating

cycle.

Heating one compule:

1. Install a compule and press the on/off button once.

2. Allow the compule to heat for two minutes. At two minutes the

temperature status LED will turn solid GREEN and the composite is warm

and ready to express.

Heating additional compules:

3. Do not turn the unit off.

4. Remove the first compule.

5. Install a new compule and immediately turn the unit off and then

back on.

6. Allow the compule to heat for one minute. At one minute the temperature

status LED will turn from blinking AMBER to blinking GREEN and the

composite is warm and ready to express.

7. Additional compules can be heated by repeating steps 3 through 6.

Optional: Save time by pre-heating additional compules using the

AdDent Calset Composite Warmer.

1. Set the Calset Composite Warmer on the high temperature setting 155°F

(68°C) and allow it to reach operating temperature (20 minutes for small

trays, 30 minutes for large trays).

2. Place the desired number of compules in the Calset Tray and allow

sufficient heating time, approximately three minutes.

3. Do not turn the Compex unit off.

4. Remove the first compule.

5. Install a pre-heated compule in the Compex. The composite is ready to

express immediately.

6. Additional compules can be heated by repeating steps 3 through 5.

• Note - We suggest you try shorter and longer heating cycles to determine

the optimum heating time for the composite you are using prior to clinical

application.

• Once the heating cycle has been activated, pressing the on/off button again

will shut off the unit and switch it back into sleep mode.

• The auto shut off feature takes place after 10 minutes of ON time to

conserve battery power.

• Tip: Avoid touching the compule ejector to the patient while dispensing

material to avoid accidently ejecting the compule.

• Tip: To conserve battery power, turn off dispenser after procedure is

complete.

Caution: To avoid damage to the unit, always remove compule after

procedure is complete. Do not store the Compex HD unit with

compule installed in the compule holder.

COMPULE HEAT UP TIME

• The Compex will heat the composite from 72°F (22°C), room temperature,

to 155°F (68°C) in approximately 2 minutes.

REMOVING THE COMPULE

Caution. Some compules can forcefully eject during the removal

process. Be sure to hold your hand below the compule to catch it

when it comes out.

• To remove the compule, press down on the raised portion of the compule

ejector. This feature allows the rear of most compules to tilt down for easy

removal.

CLEANING/DISINFECTING/STERILIZING

a) Cleaning the silicone sleeve:

• Immerse/thoroughly drench parts in a surface decontaminate cleaner

(soap and water cleaning solution).

• After 10 minutes, scrub with an instrument cleaning brush until visibly free

from debris.

• Rinse all parts with warm water.

b) Sterilizing the silicone sleeve:

• Sterilize in a steam autoclave using distilled water at a temperature of

270°F (132°C) for 20 minutes.

• Do not add chemical solutions to the autoclave.

• Do not use a chemical autoclave.

c) Disinfecting: The Compex HD housing can be disinfected following these

guidelines:

• Wipe all surfaces with a disinfectant comprising 72% - 55% alcohol and

.33% -.5% quaternary ammonium and follow the manufacturer's directions.

Some popular disinfectant wipes in this category are:

1 - Monarch Surface Disinfectant Wipes (Air Techniques)

2 - Opticide 3 Wipes (Biotrol)

3 - Super Sani-Cloth Wipes (PDI)

• Wipe, do not spray, solution onto the Compex HD housing. Prevent liquids

from entering openings on unit.

Do not autoclave the Compex HD unit. Doing so will damage the

unit and invalidate the warranty.

In order to protect this device and help prevent cross contamination we have

developed a disposable barrier bag and an autoclavable silicone sleeve.

TROUBLESHOOTING GUIDE

Problem

Cause

1. Battery not charging

a. USB Charging cable

connection

b. No power to the USB

Power Supply.

c. Battery at end of life

2. Trigger sticking after

Composite

expressing composite

accumulated on

material.

plunger tip

3. Compule not heating

a. Composite material

accumulated on heating

element.

b. Battery discharged

(battery indicator red or

unit will not turn on)

c. Unit has turned off

after 10 minutes.

4. Compule not heating

Faulty temperature

- left side LED heat

sensor

indicator turns RED for

five seconds then turns

off.

Solution

a. Ensure USB charging

cable is securely

connected to USB

power supply and to the

Compex HD unit.

b. Ensure there is power

at the USB power supply.

c. Replace the battery

Squeeze trigger to

expose plunger tip and

use soft cloth or Q-tip

to remove accumulated

composite material.

a. Use soft cloth or Q-tip

to remove accumulated

composite material.

b. Charge battery

c. Restart heating cycle

Return unit for repair.