Atwood MPD 87083 Kurulum ve Kullanım Kılavuzu - Sayfa 2

Otomobil Parçaları Atwood MPD 87083 için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Kılavuzu indirin. Atwood MPD 87083 5 sayfaları. Power jack

Sayfayı Yazdır

HEAVY DUTY POWER JACKS

Place manual override handle (

engage drive pin. Rotate handle counterclockwise to raise or

clockwise to lower the camper.

MAINTENANCE

1. Before each use, inspect jack tubes and replace if bent or damaged.

2. If wiring is connected to battery terminal, inspect at least twice each

year for corrosion. Clean with a solution of baking soda and water,

then apply a thin coat of grease.

(

1-D) and mounting bolts (

FIG

continuity problem occurs.

Guides are only intended for use on Atwood

technicians who have successfully completed Atwood

This guide should be used in conjunction with the appropriate

Instruction Manual provided with the product and any applicable

Industry Standards. This is not intended to be a complete list.

Please direct questions concerning service of Atwood

866-869-3118 before proceeding.

PERSONAL INJURY AND/OR PRODUCT DAMAGE

• If any of the following conditions develop, the trailer must not be

used until proper corrective action is taken.

CONDITION WITH SOLUTIONS

M O T O R W I L L N O T O P E R AT E

No or low voltage ..........................Check battery & electrical connections.

Jack flange not making good ......Clean paint or dirt from coupler frame

contact to provide adequate

ground with coupler surface

Blown fuse ....................................Replace with 30 amp AWG fuse

Loose wires on ON/OFF switch ....Secure wire connections

ON/OFF switch faulty ....................Replace switch

Motor faulty ..................................Replace motor

P O O R G R O U N D

WHEN BUTTON IS PRESSED ON JACK

Jack doesn't operate ....................Inspect motor mounting bolt for Loctite

Jack operates only partially up

or down, or

Jack runs intermittently

1-C) into alignment tube and

FIG

: The motor ground screw

NOTE

1-B) must be cleaned too if a ground

FIG

products by service

WARNING

Must have minimum of 10 VDC

If Loctite

found, replace with new 1/4-20

x 3" screw and two lock washers. If bolt

unavailable, clean present bolt and hole

with wire buffing wheel. Inspect bolt

3. Once each year, extend jack as far as possible and clean inner ram

tube. Coat tube with light coat of silicone spray lubricant.

The Electric Drive Motor Landing Leg system is protected by a 30 amp

fuse. If replacement is necessary, replace only with a Buss Type AGC-30

fuse or equivalent, available in automotive supply stores.

TROUBLE SHOOTING GUIDE

M O T O R C L U T C H E N G A G E S

training.

Normal if jack leg is at fully ..........None, but let go of switch when you hear

retracted or extended position

Worn worm gear ..........................Replace jack ram

products to

Dirty inner ram tube ......................Clean ram tube and coat with light coat

Bent inner ram ..............................Replace inner ram

Clutch faulty ..................................Replace motor

Jack at angle ................................Secure mounting bolts and ensure a

Excessive tongue weights ............Determine if jack is adequate for tongue

U T I L I T Y L I G H T D O E S N O T W O R K

Loose wires on the ON/OFF ..........Secure wire connection

switch

Bad light bulb ................................Replace bulb

A M P D R AW

Range of motor ............................8-45 amps

IMPORTANT CAUTION - If equalizer bars are attached to the tow

vehicle and the trailer while operating the power tongue jack,

you may experience the motor clutching the moment the jack

sees load. This will occur because you are lifting both the tongue

of the trailer and the rear of the tow vehicle. The 1500 lb. and

2500 lb. acme screw jacks cannot lift this excessive weight. To

overcome this excessive weight, you should upgrade to the 3500

lb. power jack. The ball screw mechanism utilized in this jack

should allow you to lift this load.

Power Jack

Effective: 11/21/07

hole. If dirty, clean with a 1/4-20 tap.

the clutch

of silicone spray

support plate is used.

weight.