Atwood DA-31PE Kurulum Talimatları Kılavuzu - Sayfa 2

Setüstü Ocak Atwood DA-31PE için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Atwood DA-31PE 8 sayfaları. Lp gas drop-in cooktops

Sayfayı Yazdır

1. For proper operation of your cooking appliance:

THE CABINET MUST BE

• properly constructed.

• squared to the countertop and cabinet face

THE OPENING IN CABINET MUST BE

• level from side to side and front to rear

2. The cabinet opening must be constructed so that no combustible

material can be placed next to the cooktop sides. If there is a gap

between the cooktop and an adjacent cabinet, the gap must be closed

prior to installing the cooktop.

• 30 inches is the minimum vertical distance to combustible mate-

rial above the cooktop stove. This distance may be reduced by

using non-combustible construction in accordance with Table 2-

6.7.2 in ANSI A119.2.

3. Cabinet dimensions needed for each model are shown in CABINET &

COUNTER CUT OUT CHART. The cabinet cut-out must be located

with respect to the minimum clearances to combustible materials as

noted. When planning the location consider curtains or other com-

bustible materials installed around the cooktop.

4. When the cabinet has been prepared according to the dimensions

given and the gas line is in place, remove the cooktop from its

packaging and position the cooktop in the opening.

5. Verify that the cooktop is level from side to side and front to rear.

6. Drop-In: Secure the burner box assembly in place with wood

screws (not supplied).

D26-SV: Slip right hand of unit under counter so that the valve

shafts protrude through the two 1˝ diameter holes in the counter.

Secure to the counter with (4) sheet metal screws (not supplied).

D26-SLG: Drop unit into cutout, secure to counter with (4) #6 flat

head wood screws (not supplied).

7. Make the gas connection. All openings in the cabinetry around the

gas line must be closed at time of installation. DA-PE models with

electronic ignition: Complete the electrical connections as shown in

the WIRING DIAGRAM. For galley slide-out applications, it is highly

recommended that the negative 12 volt connection be connected

directly to the battery. Voltage supply must be between 9 and 13

VDC. Appliance electrical rating is 12VDC, 0.6A during sparking.

PRODUCT DAMAGE HAZARD

• Connect to 12VDC service only.

• Do not connect to a circuit fused for more than 3 amps.

• Do not hi-pot cooktop unless electronic ignition system has

been disconnected.

CABINET &

COUNTER

CUT OUT

CHART

Models D, DA

CUT OUT DIMENSIONS

D, DA Models - 2 Burners

D , DA Models - 3 Burners

D-26SLG

D-26SV

Minimum dimension

Overall depth of cooktop

WARNING

FIRE

CAUTION

I N

11-5/8˝

16-3/8˝

16-1/16˝

19-3/16˝

19˝

14-1/8˝

11-5/8˝

16-3/8˝

8. Turn on the gas supply.

• Do not use matches, candles or other sources of ignition to test

fittings and gas lines for leaks.

9. Check all connections for gas leaks using a non-corrosive leak

detection fluid. Do not use a soap and water solution. Leak test in

excess of 8 oz. per square inch (1/2 psi) of air pressure will invali-

date warranty.

10. a. D-26SV: Attach cam lock fastener (supplied) to a bracket con-

structed by the manufacturer (not supplied). Determine area to

mount bracket in upper portion of van that is secure and unobstruct-

ed. Unfold the cover and guards to determine the location of the

keyhole shaped slot in the upper guard. Attach assembly.

Apply control label to counter before installing burner knobs.

b. Drop-In: Remove the cooktop top and burner grates from packaging

and install grates:

11. a. SINGLE & DUAL RECTANGULAR WIRE grate models

3 burner Install the rubber feet on corner grate legs, and install

the grates on the stove top. From the underside of the cooktop,

install the spring clips over the protruding grate legs. Squeeze

the edges of the clips together and slip over the ends of the

burner grate as needed.

2 burner Install rubber feet on corner grate legs. From the top,

press spring clips into holes of cooktop. Install grate onto cook-

top, engaging middle legs into spring clips.

b. ROUND WIRE grate models -

squeeze opposite sides of the grate together and insert the

legs into the holes in the stove top from above the stove top.

c. STAMPED STEEL grate models -

place one side of the grate in the burner well, ensuring that the

clip engages the emboss in the side. Gently press the other end

of the grate downward to "snap" the grate into place.

12. REPLACE THE COOKTOP TOP

Drop-In: Position the cooktop top in place; install the thumb

screws (supplied) through the cooktop top. Tighten securely. On

DAS models, press the top downward until it "snaps" in place

on both sides. Slide the knobs over the valve stems to complete

the installation. Your cooktop is now ready for operation.

• Gas line material inside the burner box must be rated for a

minimum of 300

D-26SLG

2-1/4˝

3-1/8˝

3/4˝

2-1/2˝

3-1/8˝

2-3/8˝

5/8˝

4-1/2˝

3/4˝

4-3/8˝

3-1/8˝

1˝

WARNING

EXPLOSION OR FIRE

WARNING

FIRE

F operation.

ADDITIONAL WARNING ADDED 8.23.04

D-26SV

4-3/4˝

4˝

2-3/4˝

3˝

1-1/8˝

4-1/4˝

3-1/4˝

4-3/4˝

2-1/4˝