Auber TD400P Kullanım Kılavuzu

Kontrolör Auber TD400P için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Auber TD400P 5 sayfaları. Programmable temperature controller

Sayfayı Yazdır

AUBER INSTRUMENTS

Instruction Manual

Overview

This is a dual-output temperature controller with 8 programmable steps. It

contains one temperature probe and two independent outputs. One output is

for cooling device such as refrigerator and the other one is for heating device.

The temperature control can be programmed to vary with different time step

setting. Up to 8 temperature-time steps covering 33 days can be programmed.

It can be used for applications such as beer fermentation or convert a

refrigerator to kegerator. By using both cooling and heating devices, the

refrigerator can be controlled at specific temperature regardless in hot summer

or cold winter.

This controller is a plug and play controller. No wiring is needed for the heater

or cooler. Both the heating and cooling control modes are simple on/off control,

similar to a mechanical thermostat but with much higher precision due to

adjustable hysteresis band, precise sensor and digital read out. Anti-short

function is provided for cooling to protect the compressor from being turned on

with high pressure Freon.

Different operation temperature ranges of the two outputs can be set

separately. Once the cooling range is set, the controller program will

automatically limit the heating range to prevent both heating and cooling from

being turned on at the same time.

A digital silicon band gap sensor is used. The advantage is being much more

reliable in moisture environment than thermistor sensor. It can be immersed

over extended period of time. It also has a more uniform accuracy over an

entire specified temperature range.

Specifications

Table 1. Specifications

Temperature Control Range

Temperature Resolution

Temperature Accuracy

Temperature Control Mode

Temperature Control Output

Timer Range

Timer Resolution

Max Programmable Time

Audio Alarm

Sensor Type

Sensor Size

Ambient Temperature

Dimension

Input Power

Sensor Cable Length

Power Cable Length

Warranty: One (1) year.

2015.06

TD400P Programmable Temperature Controller

-50 ~ 105° C, -58 ~ 221° F

0.1° C (between -9.9 ~ 99° C)

1° C (between -50 ~ 10° C, 100 ~ 120° C)

0.1° F (between -9.9 ~ 99.9° F)

1° F (between -58 ~ 10° F, 100 ~ 248° F)

0.5 ° C or 0.9 ° F

On/Off Control. Heating and Cooling

10A, 120 V or 240 VAC *

Each step: 0.1 to 99.9 Hours or 1 to 999

Minutes

0.1 Hours or 1 Minute

799.2 hours or 33.3 days (for total 8 steps)

High and low limit

Silicon Band Gap Sensor

0.25" OD (6.35 mm) x 1" (25mm) long

-20 ~ 50° C (0 ~ 120° F)

91 x 140 x 46mm

85 ~ 242 VAC, 50 Hz / 60 Hz

6 ft (2 m)

3 ft (1 m)

Version 1.1 (Oct, 2017)

*: Either heating or cooling device is limited to 10 Amps. The output voltage is

same as input voltage. When the controller is plugged into 120V AC, the

output will be 120VAC. If the controller is connected to 240 VAC, the output will

be 240VAC also.

Front Panel

Display window: display temperature reading and parameters.

RUN indicator: the green LED indicator is on when the program is running.

START key: start executing the program.

PAUSE/STOP key: short press it to pause the program; long press it for 4

seconds to stop the program (only when the program is already been paused).

MUTE key: silent the alarm buzzer.

STEP key: jump to different step; check the running step.

SET key: access the program settings and parameter settings.

UP key: increase the value.

DOWN key: decrease the value.

Cooling device socket: supply power to cooling device.

Cooling device indicator: green LED indicator; it is on when the cooling

device socket is energized.

Heating device socket: supply power to the heating device.

Heating device indicator: red LED indicator lit; it is on when the heating

device socket is energized.

Basic Operation

Here are the basic operating procedures to use this controller. To fully

understand the functions on this controller, please read the entire manual.

1) Connect the temperature sensor to the sensor socket that is located on the

top of the controller. Please check the alignment of the slot on the plug with the

key on the socket. (See section 12 for details.)

2) Plug the controller's power cord to a wall outlet.

3) Set up the program and system parameters. Please read the rest of this

manual for details.

4) Connect the cooling device and/or heating devices to the output sockets on

this controller.

5) Press START key to start running the program.

WWW.AUBERINS.COM

Figure 1. Front Panel.

P1/5