AIRTRONICS 92674 RX-700 Kullanım Talimatları - Sayfa 4

Alıcı AIRTRONICS 92674 RX-700 için çevrimiçi göz atın veya pdf Kullanım Talimatları indirin. AIRTRONICS 92674 RX-700 4 sayfaları. 2.4ghz fhss-1, 7-channel full-range receiver

Sayfayı Yazdır
settinG tHe FailsaFe
The Fail Safe function automatically sets the servos to a predetermined position in the event that the signal between the transmitter and
the receiver is interrupted, whether due to signal degradation or to a low transmitter battery. For example, the Fail Safe can be set so that
the throttle servo returns to low, the elevator moves slightly up, and the ailerons move slightly right or left, to result in a shallow decent.
Programmable Fail Safe is available on channels 1 through 4 only.
1) Drop the throttle control stick all the way back to the Low Throttle position, then turn the transmitter ON.
2) Turn the receiver ON. The Bind LED on the receiver should illuminate solid blue, indicating that the transmitter and receiver are
paired, then move the transmitter control sticks to verify that the servos are operating.
The Fail Safe settings will be erased if you re-bind the transmitter/receiver pair. If you bind the same transmitter/receiver pair
you MUST repeat these procedures to setup the Fail Safe function again.
3) Move the transmitter control sticks to the desired Fail Safe position. While holding the transmitter control sticks in those positions
(generally throttle at idle and a minimal amount of elevator and/or aileron), press and hold the Bind Button on the receiver. After ~2
seconds, the Bind LED will begin to blink slowly. Continue holding the Bind Button until the Bind LED begins to blink rapidly (~2 more
seconds). Once the Bind LED begins to blink rapidly, release the Bind Button.
4) Turn the transmitter OFF to test Fail Safe operation. The servos should move to the positions that you set in step 3.
ranGe cHeckinG - low Power mode
IMPORTANT The radio control system should be range checked prior to the day's first flight and prior to the first flight after a hard
landing or after a repair. This will ensure that the transmitter and receiver are communicating properly prior to flight. This ensures the
safety of your model, yourself, and the people around you.
The Range Checking procedure describes using the receiver with an Airtronics RDS8000 2.4GHz transmitter. If using the receiver
with an Airtronics SD-10G 2.4GHz transmitter, please refer to the Range Checking section in your SD-10G Operating Manual.
1) Press and hold the Bind Button on the transmitter, then turn the transmitter ON. Continue to hold down the Bind Button for ~5 seconds.
The Bind LED will blink slowly during this time. After ~5 seconds the Bind LED will blink rapidly, then go out. Release the Bind Button
and the Bind LED will continuously blink rapidly. The transmitter is now in Low Power Mode.
The transmitter will stay in Low Power Mode for 3 minutes. After 3 minutes, the transmitter will revert to Normal mode.
2) Turn the receiver ON in your model.
3) With the transmitter in Low Power Mode, walk approximately 30 paces from your model (approximately 90 feet) and, with the help
of another person, check to make sure that the servos move without any problems. If there is a problem with servo movement, try
moving to a different position while still maintaining the same distance from your model, then check servo movement again. If there
is still a problem, DO NOT FLY. Check to make sure that all receiver, servos, switch, and onboard battery connections are correct
and secure. Check to ensure that the antenna wires are correctly mounted.
4) After you have completed your range check, turn the transmitter OFF, then turn the transmitter ON to revert back to Normal Mode.
Do not attempt to fly with the transmitter in Low Power
Mode. You will be unable to control your model once it is a
certain distance away from you. Before you fly, make sure
that the Bind LED is illuminated solid blue!
If, after checking all airborne system components and verifying correct antenna wire mounting, your radio control system still fails
the Range Check, DO NOT FLY. Please contact Airtronics Customer Service.
Airtronics is Distributed Exclusively in North America by:
Global Hobby Distributors
18480 Bandilier Circle
Fountain Valley, CA 92708
http://www.airtronics.net
4
POWER MODE
TX BIND LED STATUS
Low Power Mode
Blue - Blinking Rapidly
Normal Mode
Blue - Illuminated Solid
Telephone: (714) 963-0329
Fax: (714) 964-6236