Aucma AUS-S2 Çalıştırma Talimat Kılavuzu - Sayfa 5

Su Filtrasyon Sistemleri Aucma AUS-S2 için çevrimiçi göz atın veya pdf Çalıştırma Talimat Kılavuzu indirin. Aucma AUS-S2 7 sayfaları. Ultrafiltration under sink water filter system

Sayfayı Yazdır

Installation guide

Both of the inlet and outlet of the product have quick connector port. Quick connector is

a kind of connecting port that doesn't need tools to realize quick and secure connecting.

First, pull out the U-shaped snap ring at the port, and push the flexible plastic ring on the

port to the connecting direction, making it stick to the port, then the trumpet-shaped

plastic plug can be pulled out easily. Insert the PE pipe into the end of the port, then pull

it gently, leaving some gap between the plastic ring and the port, then insert the U-shaped

snap ring into the gap.

1.Pull Out the U-shaped Snap Ring

PE Pipe

3.Pull Out PE Pipe

Connector Port

2.Push the Flexible Plastic Ring On The Port

4.Tap water faucet installation

Drilling at the location of outlet pipe

4.1 Tools and materials needed: electric hand drill, drills, water, etc.

4.2 Locating and draw circle on the washbasin countertop according to the customer's

advice.

4.3 It should be better to choose metal-specialized drilling machine for drilling. According

to actual situation, choose suitable drills (recommendation: φ29 metal drilling machine

and φ12 drill).

4.4 Concentrating when drilling, keep safety, and avoid talking with others. During drilling

heat will be produced, water can be added to decrease the temperature.

4.5 After drilling, clean the debris and dirt caused.

4.6 If the basin or wash basin has holes for liquid soap, the holes can be directly used for

installing faucet.

Installation of faucet

4.7 Tools and materials needed: nipper pliers, faucet set,

quick connecting straightway valve, PE pipe, etc.

4.8 Screw out the nut under the faucet, put the filmed stainless

steel base plate and the big rubber mat into the threaded

bolt, then penetrate it through the countertop.

Then put the metal mat and small mat into the threaded bolt,

then screw the nut to fix the faucet to ensure the base

doesn't move.

4.9 Insert the quick connecting straightway valve into the inlet

of the faucet, make sure the connection is secured. Then cut

PE pipe into suitable length, and insert one end to the quick

connecting straightway valve.

3.Insert The U-shaped Snap Ring And Finish The Installation

Of Connector

1.Insert the PE Pipe

2.Pull The Plastic Ring Gently and Leaving Some Gap

Gooseneck Faucet

Stainless Steel Base

Rubber Pad

Plastic Pad

Internal Pad

Nut

Fast Connector

1/4 Inch PE Pipe

Installation guide

5.Connecting PE pipe

This product uses fast connecting, just insert the water pipe into the corresponding joint.

Before connecting water pipe, cut PE pipe into suitable length, and make sure the section

is smooth and tidy, in case water leakage.

1)Filtered water connection: connect one end of PE pipe into the inlet of the faucet, and

connect the other end to the connector behind the cabinet where the label of filtered water

connector is marked.

2)Inlet connection: connect one end of PE pipe onto the tap water ball valve, and connect

the other end to the connector behind the cabinet where the label of inlet water connector

is marked.

The water pipe shall be installed along with the edges of the cabinet.

Using suitable tools to do vertical cutting, cut the pipe into needed length.

Be sure not to bend the pipe during installation, in case the pipe got squeezed.

In order to make the water flow smooth and fast, the pipe connecting the cabinet and the

faucet should be as short as possible.

Filtered Water Faucet

PE Pipe

6.Installation of battery

Using screw driver to unscrew the battery compartment , put the battery into the

compartment, screw the nut.

Inlet Three

-way Ball

Valve