3onedata TNS5800 Series Hızlı Kurulum Kılavuzu - Sayfa 3
Anahtar 3onedata TNS5800 Series için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. 3onedata TNS5800 Series 4 sayfaları. Layer 3 rack-mounted industrial ethernet switch
Ayrıca 3onedata TNS5800 Series için: Hızlı Kurulum Kılavuzu (4 sayfalar), Hızlı Kurulum Kılavuzu (3 sayfalar), Hızlı Kurulum Kılavuzu (5 sayfalar), Hızlı Kurulum Kılavuzu (4 sayfalar)
Sayfayı Yazdır
2
D0- (DA-)
The first group of bi-directional data
of Gigabit Ethernet negative
3
D1+ (DB+)
The second group of bi-directional
data of Gigabit Ethernet positive
4
D1- (DB-)
The second group of bi-directional
data of Gigabit Ethernet negative
5
D3+ (DD+)
The fourth group of bi-directional
data of Gigabit Ethernet positive
6
D3- (DD-)
The fourth group of bi-directional
data of Gigabit Ethernet negative
7
D2- (DC-)
The third group of bi-directional data
of Gigabit Ethernet negative
8
D2+ (DC+)
The third group of bi-directional data
of Gigabit Ethernet positive
Model
II
Model
10/100/1000Base-T(X)
interface type is M12 X-Coded 8-Pin slot
(female) and its pin definitions are as
follows:
No.
Definition
Description
1
BI + (DA+)
The first group of bi-directional data
of Gigabit Ethernet positive
2
BI - (DA-)
The first group of bi-directional data
of Gigabit Ethernet negative
3
BI + (DB+)
The second group of bi-directional
data of Gigabit Ethernet positive
4
BI - (DB-)
The second group of bi-directional
data of Gigabit Ethernet negative
5
BI + (DD+)
The fourth group of bi-directional
data of Gigabit Ethernet positive
6
BI - (DD-)
The fourth group of bi-directional
data of Gigabit Ethernet negative
7
BI - (DC-)
The third group of bi-directional data
of Gigabit Ethernet negative
8
BI + (DC+)
Console Port Connection
This device provides 1 program debugging port based on
RS232, which could be connected to PC for device CLI
command management. The interface adopts RJ45 port. The
pin definitions of RJ45 are as follows:
No.
Definition
【Restoring Factory Settings】
The steps of restoring factory settings of Model II Model III are
as follows: press and hold restore factory setting button to
power on the device again. Release the button after 3-4s to
finish restoring factory settings.
【Checking LED Indicator】
III
provide
20
This device provides LED indicators for monitoring the work
interfaces.
The
status of the device, which has simplified the troubleshooting
process comprehensively. The function of each LED is
described in the table as below:
LED
Status
ON
PWR
OFF
ON
ALARM
OFF
ON
RUN
OFF
Blinking
ON
Link/Act
Blinking
OFF
The third group of bi-directional data
of Gigabit Ethernet positive
2
3
5
TXD
RXD
GND
Description
PWR is connected and running
normally
PWR is disconnected and running
abnormally.
Power supply, port link alarm
Power supply, port link without
alarm
The device is powered on or the
device is abnormal.
The device is powered off or the
device is abnormal.
Blink 1 time/s, system is running
well.
Ethernet port connection is active.
Data transmitted
Ethernet port connection is inactive.
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device's configuration interface via IE
browser is shown as below:
Step 1
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed.
Step 2
Enter device's IP address in the address bar of the
computer browser.
Step 3
Enter device's username and password in the login
window as shown below.
Click "OK" button to login to the WEB interface of
Step 4
the device.
Note:
The default IP address of the device is "192.168.1.254".
The default username and password of the device is
"admin123".
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.