Dan D'Agostino PROGRESSION M550 Kullanıcı El Kitabı - Sayfa 6
Amplifikatör Dan D'Agostino PROGRESSION M550 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Dan D'Agostino PROGRESSION M550 9 sayfaları.
Sayfayı Yazdır
Note: When the Progression amplifier is in operational mode, the 12 V trigger provides
12 volts of DC output. When the amplifier is in standby mode or off, the DC output is 0 volts.
A maximum of 500 mA is available from the 12 V trigger output. Consult the owner's manual
of the components used in the system to take full advantage of the remote capabilities of the
Progression amplifier.
OPERATION
Initial power-up of the amplifier
Move the rear panel power breaker switch to the up position to place the amplifier in standby
mode. The main power button is located on the front underside edge of the amplifier. Pressing
the button will power up the amplifier and illuminate the power meter.
Note: If the 12V trigger input is being used, the amplifier is moved from standby to operation
and vice versa by the 12V trigger output provided by device connected to the 12V trigger
input. The main power button is not operable.
After power is switched on, the Progression amplifier requires approximately 30 minutes to
reach optimal operating temperature. Although the amplifier will sound excellent upon initial
listening, the sound quality will improve as it warms up.
During operation
The Progression amplifier requires no adjustments during normal operation. If there is no sound
or the sound quality is in some way impaired, consult the Troubleshooting section in this manual.
Light switch
This switch has three positions. Move it to the left (when looking at the amp from the rear) for
low brightness and to the right for high brightness. The center position, off, turns the meter
illumination completely off.
MAINTENANCE
The Progression amplifier requires no user maintenance other than to keep it clean and ensure
that the vents remain unobstructed.
To clean the amplifier, first disconnect the AC plug. Spray a small amount of distilled water or
a cleaning solution such Endust® or Pledge® onto the supplied microfiber cloth and gently wipe
the amplifier's surface along the direction of the metal grain, with light pressure only. Never
use a circular motion or heavy pressure, as this can permanently scratch the machined surfaces.
Do not spray the cleaner directly onto the amplifier.
8
If dust or other contaminants or objects collect around the heat sink venturis or the vents at
the top and bottom of the amplifier, remove small objects by hand and use a shop vacuum or
hand vacuum to remove the dust. Use a brush attachment on the vacuum to avoid scratching
the amplifier's surface.
TROUBLESHOOTING
Amplifier will not power up
If the front meter is not illuminated, follow the procedure outlined below. If one step succeeds
in activating the power, stop there and ignore the other steps.
1. Push the power switch on the front underside edge of the amplifier.
2. Check to make sure the AC cord is plugged into the wall outlet.
3. Check at the back of the amplifier to make sure the IEC connector is pushed all the way
into the jack on the back of the amplifier.
4. Check your household electrical box to make sure the circuit breaker has not been tripped.
If it has, flip the breaker back on.
5. If the breaker trips again, check the speaker cable connection(s) on the amplifier and the
speaker(s) to make sure that the terminals are not shorted, and check the entire length of
the cable(s) to ensure there is no damage.
6. If all of these steps fail to return power to the amplifier, consult your dealer for service.
Front meter is illuminated but you hear no sound
Follow these steps in order. If one step succeeds in restoring sound, stop there and ignore
the other steps.
1. Check your preamp and source device to make sure they are both turned on.
2. Check the source device to make sure it is playing; i.e., if it's a record player, make sure it's
spinning and the tonearm is lowered, or if it's a CD player, make sure it's in play mode and
not in pause.
3. Make sure your preamp is not muted and that the desired source is selected.
4. Check the line-level connections between the source device and the preamp, and between
the preamp and the amplifier(s). Reconnect any cables that may have become disconnected.
5. Check the cables between the amplifier(s) and the speaker(s) to make sure they are
properly connected and that the cables have not become damaged.
6. If you have a spare pair of interconnect cables (even cheap ones will work temporarily),
try using them between the source device and the preamp and between the preamp and
the amplifier. If this restores sound, replace the defective cables.
7. If all of these steps fail to restore sound, consult your dealer for service.
9