Elite Acoustics Engineering A6-55 Hızlı Başlangıç Kılavuzu - Sayfa 2
Amplifikatör Elite Acoustics Engineering A6-55 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Elite Acoustics Engineering A6-55 13 sayfaları. Acoustic guitar and vocal amplifier with 6 channels, mixer, effects, lithium battery and bluetooth
Sayfayı Yazdır
1.
Battery Switch [37] is set to Connect. (Battery Switch is set to Disconnect position to
preserve battery life for transit or storage.)
2.
Make sure the SPEAKER VOLUME [3] control is down before you turn the POWER [38]
on.
3.
Connect the input of your microphone to the MIC IN [18]. Or you can connect a ¼" line
input from an instrument [17]. You can also connect an additional mono or stereo [20].
All EQ knobs (21) should be set to 12 o'clock (FLAT EQ), Notch Filter knob (19) should
be also in the 12 o'clock. MUTE switch (13) and Phase switch (15) is out. EFX send level
(14) should be at minimum.
4.
Turn on the POWER [38] switch, battery meter should be all GREEN (indicate battery is
fully charged)
5.
EFX MIX knob (8) should be set to 12 o'clock. EFX should be bypassed until you are
ready to test EFX. Monitor EQ (6) should be set to 12 o'clock "FLAT EQ"
6.
Turn up GAIN [12] until there is a solid green light showing "signal"[CHAN 1 meter] at
desired level, without a red "peak"[CHAN 1 meter] light, indicating too much signal.
Some MIC or INPUTs can distort the Speaker even with Gain Knob (12) at Minimum.
Press the PAD switch (16) to reduce the input signal level to avoid distortion if input
signal level is too high.
7.
Adjust the SPEAKER VOLUME [3] to a comfortable level.
8.
If you want to test Bluetooth® streaming, Connect device to Bluetooth® [40]
9.
Recommended Monitor EQ (6) setting for Bluetooth playback - High and Mid (12 o'clock)
Low (1 - 2 o'clock)
10. Note if you are using an iPhone or iPad via Bluetooth®, set the volume on your device
about halfway. Maximum volume will distort. The Monitor Sigle (GREEN) LED is a good
indication of a good input level from your Bluetooth or AUX inputs.
11. Use Channel 1 for your Acoustic Guitar and Channel 2 for your vocal.
12. when you are getting a good sound without CHAN EQ or EFX, time to start playing with
the CHAN EQ and EFX - start with these recommended setting and adjust to achieve the
tone you prefer.
13. Acoustic Guitar EQ setting recommendations.
Low Volume - High (1 o'clock) Mid (12 o'clock) Low (1 o'clock)
14. Acoustic Guitar EQ setting recommendations.
Medium Volume - High (2 o'clock) Mid (11 o'clock) Low (2 o'clock)
15. Acoustic Guitar EQ setting recommendations.
High Volume - High (12 o'clock) Mid (9 o'clock) Low (12 o'clock)
16. Set you vocal EQ FLAT to start and ajdust EQ as you need.
17. Release the EFX mute switch (11)
18. Set EFX send level knob (14, 24, 31) on each channel to about 3 o'clock.
19. Select R2 - Reverb - Dark Cavern.
20. Turn EFX Parameter Knob (9) to 12 o'clock.
21. Turn Mix Knob (11) to 5 o'clock. Slowly turn it CCW to achieve the level of EFX you
prefer.