Ducati SW400 Manuel - Sayfa 8
Kapı Açıcı Ducati SW400 için çevrimiçi göz atın veya pdf Manuel indirin. Ducati SW400 11 sayfaları.
Sayfayı Yazdır
DUCATI
How to install the actuator
The control unit box must be placed outside the reach of children and unauthorized
persons, (at a suggested high of min. 1,2 m from the ground) preferably with a
minimum distance of 60 cm from the actuators. If the control unit is not installed next
to the gate but remotely, for example in a control room, an external radio receiver
must be added to the system, which receives the radio signal in proximity of the
gate.
The actuators must be connected to the main electronic board by a outdoor use
bipolar electric cable H07NRF min 1 mmq.
The accessories must be connected with an outoor use min. 0.5 mmq electric
cable. (Cables, screws and dowels on the structure are not provided, but must
be purchased separately according to the system and the specific material and
dimension of the structure).
Automatic gate opener essential components
The minimum components needed to automate a swing gate are:
1= Control box with containing electronic board with on board radio receiver, toroidal
transformer, inner battery compartment.
2 = actuators
3 = blinking light
6 = radio remote control
Useful additional componentsto complete the automatic gate system:
4 = external antenna
5 = key switch
7 = radio keypad
8 = solar panel
9 = pair of photocells ( receiver + transmitter) & pair of photocells integrated in
coloumns
+ GSM module and /or GSM Intercom to command your gate opener by your
mobilephone
Gate opening towards inside (pull to open) or outside the property (push to
open)
CAUTION: the most common types of gates are those with opening to the inside
of the property. It is however also possible to automate gates that open out of the
property following the following warnings:
to automate a gates that opens towards inside the property, it is necessary to use
a compatible actuator model (telescopic actuators are recommended). check the
specific actuator diagram (page10-22) to verify it is compatible for installation on
gate that opens towards outside.
NOTE: in the case of gate opening to the outside ( PUSH-TO-OPEN) , it is
necessary to reverse the polarity of motor cable wiring (check electronic wiring
diagram of your electronic board model (page 36-52)
Check the feasibility of such a system considering the lateral overall dimensions.
Make sure the gate wings do not open on a public passageway (This may be
prohibited by specific national or local law, and you may be held liable for damages
or injuries caused to third-party)
It is advisable to equip the system with a safety light barrier (photocells), which
should be positioned so that the wings do not cause any damage or disturbance to
any passing pedestrians, bikes or parked vehicles.
4. HOW TO INSTALL THE ACTUATOR:
The actuators must be installed inside your property.
First of all you should determine the height at which the actuators will be positioned.
They should be preferably installed at a height between the two hinges, remember
they must always match a reinforced horizontal cross of the gate to ensure the
actuator is installed in a resistant part of the structure of your gate.
Warning: the actuator should never be installed less than 15 cm from the ground
Warning: the actuators must be installed horizontally in line with the gate: Check
with a spirit level that the gate is perfectly balanced and make sure the drive is
in balance with the gate. Take into account that if the actuator is not installed in
line with the gate, it may causea point of majour friction during travel, incorrect
operationand damages.
Identify the exact model of the actuator delivered in your gate opener package kit
(see table page 4-5) and verify that the installation limits and the maximum A and B
measures your stucture must comply to be compatible with your actuatoethat your
actuator
are respected.
4.1 – Post mounting bracket
Pillar/ Coloumn/ fence post: determinate the position where to install the post
mounting bracket
According to the actuator model, and to the pillar/wall dimension, calculate the ideal
fixing position of the rear bracket by consulting the installation schema of your
29