Dancing Wings Hobby 1.8M 1:5 Savage Bobber Kullanım Kılavuzu - Sayfa 2
Oyuncak Dancing Wings Hobby 1.8M 1:5 Savage Bobber için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Dancing Wings Hobby 1.8M 1:5 Savage Bobber 8 sayfaları. Balsawood scale airplane
Sayfayı YazdırKIT
配件图仅做参考用，您收到的实物可能因为修改/优化的原因导致与图片有略有不同。
Photos shown here just for reference, the product you received maybe slightly
differ from the photos due to continuous improvement on products.
SCG33-A
SCG33-B
SCG33-G.1
SCG33-A:机身 Fuselage
SCG33-B:机翼 Wing
SCG33-D:水平尾翼 Horizontal tail
SCG33-E:起落架 Landing Gear+机轮 Wheels
SCG33-F:垂直尾翼 Vertical tail
SCG33-G:机翼支架 Wing strut
SCG33-H：
螺丝及配件 Screws and accessories
舵角 Rudder horn
木块，木杆 Wood block; Wood rod
连杆 Connecting rod
★
装配提示符号
Assembly symbol guide
确保自由转动
使用适量快干胶粘固
Ensure free rotation
Use medium CA
用力推入
用模型刀切割
Push tightly
Use hobby knife with
x2
重复拼装
涂抹螺丝胶
Repeat multiple times
Apply threadlock
1
SCG33-D
SCG33-F
SCG33-E.1
SCG33-E
SCG33-C
SCG33-G
I
SCG33-H
L
K
SCG33-G.2
J
SCG33-C:机头罩 Cowling
I:尾轮组件 Tail wheel
J:碳管 Carbon tube
K:PVC 风挡 PVC window shield
使用少量快干胶粘固
Use thin CA
拧紧安装
Fully Tighten
OIL
左右对称安装
Assemble right
Epoxy glue
and left
01
起落架安装
Assemble the Landing Gear
01-1
SCG33-E
02
尾翼及尾轮安装
Assemble the Tail Wing and Tail Wheel
02-1
在升降舵预切的开口处插入纸合页，并把舵面插入尾翼，
用快干胶粘固连接处。并保持舵面可以自由转动。
Insert the paper hinges into the pre-cut openings in
the elevator, and insert the rudder surface into the
tail,finally glue the joints with quick-drying glue.
Make sure to keep the rudder surface free to turn.
用铅笔做记号
Use a pencil
02-3
加润滑油
Apply Oil
使用环氧胶粘固
Use epoxy adhesive
按上图所示切除多余部分的蒙皮
Cut off the spare part of the covering film as shown above
01-2
螺丝 screw
M3x15mm
SCG33-E.1
轮挡
wheel stopper
螺丝 screw
M3x15mm
SCG33-D
02-2
02-4
安装垂直尾翼到机身尾部，用大量环氧胶粘固。
Install the vertical tail to the rear of the fuselage and glue firmly
with a lot of epoxy glue.
SCG33-A
Epoxy glue
2