3Shape TRIOS S3A-22 Kurulum Kılavuzu - Sayfa 6

Dişçilik ekipmanları 3Shape TRIOS S3A-22 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. 3Shape TRIOS S3A-22 14 sayfaları.

Sayfayı Yazdır

Step 4: Connect the other end of the Ethernet cable to the PC

(if no Ethernet ports are available in the PC, use an Ethernet-to-USB adapter) .

Step 5: Connect the power (mains) cord to the power supply . The other

end of the power (mains) cable goes into a grounded power outlet

(not shown in the Figure) . To isolate the pod and thus the scanner from

supply mains, unplug the power cord from mains .

Step 6: Insert a battery fully into the rear of the scanner . (Figure 5, S26)

or Insert the TRIOS 4 cord into rear of scanner (Figure 5, S27) .

Step 7: Place the scanner in the pod .

Scanner Battery Charging (Figure 1, S9 and S10):

Before you start: Place the battery charger either on a flat surface hori-

zontally or attach it to the wall mount vertically, with battery containers

pointing upwards .

Step 1: Attach the power cord and plug it to mains power .

Step 2: Push the batteries one by one into the charger until they click into

place . When charging, the LED above each battery will indicate the status:

• A pulsating green means that charging is ongoing;

• Constant green means that the charging is completed;

• Yellow means that an error has occurred, either the battery is not

inserted correctly, or the charging is outside operating conditions

for temperature .

CAUTION

If the charger continues to indicate yellow, the battery

is damaged and should be discarded, unless the battery

is too hot or too cold (see section 4 .8) .

4.8 Starting and Shutting Down TRIOS

Please follow the steps below to start TRIOS IOS system for the first time:

Step 1: Turn the system ON .

S3A: Press the standby button on the top of the backside of the display .

The TRIOS software starts automatically .

S3P: Start the PC . If the PC has no TRIOS software pre-installed, please

install the TRIOS software first . In case of difficulties with software instal-

lation, plase contact 3Shape support .

Step 2: Log on using a default TRIOS Operator .

Step 3: Configure and use your TRIOS IOS system .

For models S3P-8, S3A-10, S3A-18

The wired scanner turns on automatically when the MOVE/MOVE+ cart

is turned on, or when the smart cord is plugged into the scanner .

For models S3P-2, S3A-14, S3A-22

To activate the wireless scanner, press the button on the top of the

scanner when the MOVE/MOVE+ cart or computer is turned on .

The scanner can be turned off manually by removing the battery .

Follow on-screen instructions for connecting to the wireless scanner .

When using the TRIOS IOS system, the user is guided by messages shown

in the TRIOS software . This includes when calibration of the scanner

is due . Other messages include a reminder to mount the scanning tip:

"Please make sure the scanning tip is mounted on the scanner . "

Calibration

A calibration of the handheld TRIOS scanner is required before using TRIOS

for the first time, or to compensate for thermal variation and aging effects

due to wear . During regular use the TRIOS software will prompt the user

when calibration is due . To perform the calibration, attach a cleaned and

sterilized or high-level disinfected scanner tip on the scanner tube .

Remove the sleeve from the calibration target .

Mount the calibration target on the calibration adaptor with the grey side,

marked with the letter B, facing up .

Attach the calibration adaptor to the cleaned and sterilized or high-level

disinfected scanner tip . Go to the Settings page in the TRIOS software, select

TRIOS → Scanner Management → 3D calibrate scanner, and then follow the

on-screen instructions . Remember to save changes when prompted .

For a more detailed description of the 3D calibration, please refer to the

TRIOS online help .

Color Calibration

A color calibration of the handheld scanner is required

before each scan in order to get optimal colors .

Attach a cleaned and sterilized or high-level disinfected

scanner tip on the scanner tube .

Remove the sleeve from the color calibration target .

Mount the color calibration target to the calibration adaptor

with the color side, marked with the letter A, facing up .

Attach the calibration adaptor to the cleaned and sterilized

or high-level disinfected scanner tip .

Go to the Settings page in the TRIOS software, select TRIOS → Scanner

Management → Color calibrate scanner, and then follow the on-screen

instructions, which will also include validation of the performed color cali-

bration . Remember to save changes when prompted .

For a more detailed description of the color calibration,

please refer to the TRIOS online help .

Proper shutdown

Inside the TRIOS software, click on the Power button and select Shutdown

or press the the standby button on the back of the monitor on the MOVE/

MOVE+ cart . System S3A (MOVE/MOVE+ cart) only: The light under the

standby button turns off to confirm that the system is shut down .

CAUTION

When switching off the system, allow enough time for it to

shut down properly before disconnecting the mains cable .

System S3A (MOVE/MOVE+ cart) only

IMPORTANT NOTICE

The standby button can also be used to force TRIOS IOS

system to shut down in case the screen stops responding .

To force a shutdown, push and hold the standby button

pressed for about 5 seconds . Then, restart the system .

4.9 Starting TRIOS Online Help

The TRIOS online help can be started from the TRIOS software by clicking

on the Help button and choosing User Manual .