Danfoss ECL Comfort 210 Kullanıcı Kılavuzu - Sayfa 3

Termostat Danfoss ECL Comfort 210 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Danfoss ECL Comfort 210 6 sayfaları. Extended heat cut-out
Ayrıca Danfoss ECL Comfort 210 için: Kullanıcı Kılavuzu (12 sayfalar), Kullanıcı Kılavuzu (12 sayfalar), Kurulum Kılavuzu (4 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kullanım Kılavuzu (16 sayfalar), Kullanım Kılavuzu (10 sayfalar), Kurulum Kılavuzu (7 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (16 sayfalar), Montaj Kılavuzu (16 sayfalar)

Sayfayı Yazdır
Danfoss ECL Comfort 210 Kullanıcı Kılavuzu
7.0 Frequently asked questions
The time shown in the display is one hour
off ?
See 'Time and Date' .
The time shown in the display is not
correct?
The internal clock may have been reset, if
there has been a power break for more than
72 hours.
Go to the 'Common controller settings' and
'Time & Date' to set the correct time.
The ECL Application Key is lost?
Switch the power off and on again to see the
system type and the software generation of
the controller or go to 'Common controller
settings' >'Key functions' > 'Application' .
The system type (e.g. TYPE A266.1) and the
system diagram is displayed.
Order a replacement from your Danfoss
representative (e.g. ECL Application Key
A266).
Insert the new ECL Application Key and copy
your personal settings from the controller to
the new ECL Application Key, if required.
The room temperature is too low?
Make sure that the radiator thermostat does
not limit the room temperature.
If you still cannot obtain the desired room
temperature by adjusting the radiator
thermostats, the fl ow temperature is too
low. Increase the desired room temperature
(display with desired room temperature).
If this does not help, adjust the 'Heat curve'
('Flow temp. ' ).
The room temperature is too high during
saving periods?
Make sure that the min. fl ow temperature
limitation ('Temp. min. ' ) is not too high.
DEN-SMT/DK
10
How to make an extra comfort period in
the schedule?
You can set an additional comfort period
by adding new 'Start' and 'Stop' times in
'Schedule' .
How to remove a comfort period in the
schedule?
You can remove a comfort period by setting
'Start' and 'Stop' times to the same value.
How to restore your personal or the
factory settings?
See the Installation Guide. Additional
documentation for ECL Comfort 210 and
310, modules and accessories is available on
http://den.danfoss.com/.
Why can't the settings be changed?
The ECL Application Key has been removed.
How to react on alarms ( )?
An alarm indicates that the system is not
operating satisfactorily. See the Installation
Guide. Additional documentation for
ECL Comfort 210 and 310, modules and
accessories is available on
http://den.danfoss.com/.
VI.KT.Y1.02
Danfoss District Energy
Thank you for buying a Danfoss product
Table of Contents
1.0 Symbols .......................................................................................................................................................4
2.0 How to navigate.........................................................................................................................................5
3.0 Choose your favorite display .................................................................................................................6
4.0 Setting temperatures ...............................................................................................................................7
5.0 Setting your personal schedule ...........................................................................................................8
6.0 Holiday program ........................................................................................................................................9
7.0 Frequently asked questions................................................................................................................ 10