Casio 2752 Kullanım Kılavuzu - Sayfa 3

İzle Casio 2752 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Casio 2752 6 sayfaları.

Casio 2752 Kullanım Kılavuzu
Operation Guide 2752
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use B and D to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
• Pressing A in the World Time Mode causes the
applicable city code to appear on the digital display for
about one second.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
DST indicator
• Note that you cannot use the World Time Mode to change the DST setting of the
Home City code you currently have selected in the Timekeeping Mode. See "To
change the Daylight Saving Time (summer time) setting" for information about
turning the Home City code DST setting on and off.
• Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT
is selected as the city code.
• The DST indicator will appear on the display whenever you display a city code for
which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
Alarms
You can set five independent daily alarms. When an alarm
Mode indicator
is turned on, the alarm tone sounds when the alarm time
is reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The alarm number (
screen.
00
is shown for the alarm time when the Hourly
Time Signal screen is on the display.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm number
Alarm time
(Hour : Minutes)
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
Hourly time signal
screens until the one whose time you want to set is
on indicator
displayed.
Alarm on
indicator
A1
00
2. Hold down A until the hour digits of the alarm time
start to flash, which indicates the setting screen.
• This automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds in all modes at the preset time for about 10 seconds, or until you
stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down B to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select an alarm or the Hourly Time Signal.
2. When the alarm or the Hourly Time Signal you want to set is selected, press B to
turn it on and off.
Indicates alarm is ON.
Indicates Hourly Time Signal is ON.
• The alarm on indicator (
) and the Hourly Time Signal on indicator (
on the display in all modes while these functions are turned on.
• If any alarm is on, the alarm on indicator is shown on the display in all modes.

Countdown Timer

You can set the countdown timer within a range of one to
Mode indicator
60 minutes. An alarm sounds when the countdown
reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
To set the countdown start time
Seconds
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
Minutes
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the procedure under "To use the
countdown timer" to display it.
2. Press C to move the flashing in the sequence shown below to select other
settings.
Minutes
3. While a setting is flashing, use D (+) and B (–) to change it.
• See "To turn auto-repeat on and off" below for details on the auto-repeat setting.
4. Press A to exit the setting screen.
through
) indicates an alarm
A1
A5
A2
A3
A5
A4
) are shown
Auto-
repeat
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press B. This returns the countdown time to its starting value.
To turn auto-repeat on and off
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
2. Press C to move the flashing to the auto-repeat
setting.
3. Press D to turn auto-repeat on (
off (
displayed).
4. Press A to exit the setting screen.
• When auto-repeat is turned on, the alarm sounds and
Number of repeats
countdown starts again whenever the countdown
reaches zero. You can stop the countdown by pressing
D, and manually reset to the countdown start time by
pressing B.
• Auto-repeat timing repeats up to nine times.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
Mode indicator
and two finishes.
• The display range of the stopwatch is 99 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Minutes
• All of the operations in this section are performed in the
Seconds
Stopwatch Mode, which you enter by pressing C.
1/100 second
To measure times with the stopwatch
Elapsed Time
D
D
D
Start
Stop
Re-start
Split Time
D
B
B
Start
Split
Split release
Two Finishes
B
D
D
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
Illumination
The watch has an EL (electro-luminescent) panel that
Auto light switch
causes the entire display to glow for easy reading in the
indicator
dark. The watch's auto light switch automatically
illuminates the face when you angle the watch towards
your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See "Illumination Precautions" for other important
information.
To turn on illumination manually
In any mode, press L to illuminate the display for about
one second.
• The above operation turns on illumination regardless of
the current auto light switch setting.
About the Auto Light Switch
Turning on the auto light switch causes the display illumination to turn on for about one
second, whenever you position your wrist as described below in any mode. Note that
this watch features a "Full Auto EL Light," so the auto light switch operates only when
available light is below a certain level. It does not illuminate the display under bright
light.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
surprise or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle, or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
displayed) and
D
B
Stop
Clear
B
D
Clear
Stop
B
B
Split release
Clear
Display time of
second runner.
More than
40°
3