Casio W213D-1AVCF Kullanım Kılavuzu - Sayfa 2

İzle Casio W213D-1AVCF için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Casio W213D-1AVCF 2 sayfaları. Casio w213d-1avcf: user guide

Sayfayı Yazdır

Operation Guide 3170

To select the operation of Alarm

1. In the Alarm Mode, use D to select Alarm

2. Press A to cycle through the available settings in the sequence shown below.

Snooze on indicator (

Press

One-time

Snooze

alarm on

• The snooze on indicator (

) and Alarm

• The snooze on indicator (

) flashes during the 5-minute intervals between

alarms.

• The alarm indicator (Alarm

on and/or snooze on) flashes while the alarm is

sounding.

Countdown Timer

The countdown timer can be set within a range of

one minute to 24 hours. An alarm sounds when the

countdown reaches zero.

• You can also select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

Seconds

Minutes

To use the countdown timer

Hours

Press D while in the Countdown Timer Mode to start the

countdown timer.

• When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is automatically reset to its starting value after the alarm stops.

• The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

• Press D while a countdown operation is in progress to pause it. Press D again to

resume the countdown.

• To completely stop a countdown operation, first pause it (by pressing D), and then

press A. This returns the countdown time to its starting value.

To set the countdown start time

1. In the Countdown Timer Mode, hold down A until the

hours setting of the countdown start time starts to flash,

which indicates the setting screen.

2. Press C to move the flashing between the hours and

minutes settings.

3. While a setting is flashing, use D to increase it.

• To set the starting value of the countdown time to

24 hours, set

4. Press A to exit the setting screen.

To turn auto-repeat on and off

1. In the Countdown Timer Mode, hold down A until the

Auto-repeat indicator

hours setting of the countdown start time starts to flash,

which indicates the setting screen.

2. Press B to toggle auto-repeat on (

off (

not displayed).

• Note that pressing B in the above operation also turns

on the backlight.

• When the end of the countdown is reached while

auto-repeat is on, the alarm sounds, but the countdown

restarts from the beginning without stopping. You can

stop the countdown by pressing D and manually reset

to the start time by pressing A.

• The auto-repeat indicator appears in the Countdown

Timer Mode only.

Stopwatch

The stopwatch lets you measure elapsed time, split times,

1/100 second

and two finishes.

• The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

Seconds

elapsed time measurement.

Minutes

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

Hours

To measure times with the stopwatch

Elapsed time

Start

Stop

Re-start

Split time

Start

Split

Split release

(SPL displayed)

Two Finishes

Start

Split

Stop

First runner

Second runner

finishes.

Display time of

first runner.

) and Alarm

on indicator

on indicator are displayed in all modes.

0:00

displayed) and

Stop

Clear

Stop

Clear

Split release

Clear

Display time of

second runner.

Dual Time

The Dual Time Mode lets you keep track of time in a different time zone.

• In the Dual Time Mode, the seconds count is synchronized with the seconds count

of the Timekeeping Mode.

To set the Dual Time

1. Press C to enter the Dual Time Mode.

2. In the Dual Time Mode, hold down A until the hour

setting starts to flash, which indicates the setting

screen.

3. Press C to change the selection in the following

sequence.

Hour

Seconds

Hour : Minutes

4. Press D to increase the setting.

5. Press A to exit the setting screen.

Backlight

The backlight uses an LED (light-emitting diode) and a

light guide panel that cause the entire display to glow for

easy reading in the dark.

• See "Backlight Precautions" for other important

information about using the backlight.

To turn on the backlight

In any mode, press B to illuminate the display for about

one second.

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Auto return features

If you leave a screen with flashing digits for two or three minutes without performing

any operation, the watch automatically saves any settings you have made up to that

point and exits the setting screen.

Data and Setting Scrolling

The D button is used to scroll through setting screen data on the display. Holding

down this button during a scroll operation scrolls through the data at high speed.

Backlight Precautions

• The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

• The backlight automatically stops illuminating whenever an alarm sounds.

• Frequent use of the backlight shortens the battery life.

Specifications

Accuracy at normal temperature: ±30 seconds a month

Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week

Time system: Switchable between 12-hour and 24-hour formats

Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099

Alarms: 5 Multi-function ∗ alarms (Four one-time alarms; one snooze/one-time alarm);

Hourly Time Signal

∗ Alarm type: Daily alarm, Date alarm, 1-month alarm, Monthly alarm

Countdown Timer

Measuring unit: 1 second

Input range: 1 minute to 24 hours (1-minute increments and 1-hour increments)

Other: Auto-repeat function

Stopwatch

Measuring unit: 1/100 of a second

Measuring capacity: 23:59' 59.99''

Measuring modes: Elapsed time, split time, two finishes

Dual Time: Hour, minutes, seconds, p.m. (P)

Other: Backlight (light-emitting diode)

Battery: One lithium battery (Type: CR2025)

Approximately 10 years on type CR2025 (assuming alarm operation 10 sec./day,

and one backlight operation 1.5 sec./day)

Minutes