Freedom Freedom 200+p Kullanıcı El Kitabı - Sayfa 5
Araba Alarmı Freedom Freedom 200+p için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Freedom Freedom 200+p 7 sayfaları.
Sayfayı YazdırShock Detection And Prewarn Circuit
This system allows the easy addition of an auxiliary sensor which will activate the system
if a shock or impact to the vehicle is detected. Your system is equipped with a Prewarning
feature, which requires connection of an Dual-Zone sensor. When equipped, a minor impact
will cause the security system to respond by chirping the siren for two seconds. After this
feature has been activated 5 times it will automatically shut down until the system is rearmed
again. If the vehicle experiences a major impact, a Dual-Zone sensor will fully activate the
security system.
Trunk Release And 3rd Channel Output
The FREEDOM-200+P has two additional outputs for enhanced flexibility and conve-
nience. The first of these outputs is commonly used for trunk or rear hatch release. This
output is activated by pressing and holding the transmitter's small button for two seconds.
This operation may also be programmed to automatically disarm the system if it is armed.
The 3rd Channel output is commonly used to activate optional equipment such as remote
car starters. This feature is enhanced especially for remote starting: the when 3rd Channel
is utilized, system will ignore the shock sensor and ignition circuits if it is armed. Further,
if any of the other trigger circuits are violated, the system will be activated and the remote
starter will be turned off, stopping the engine. Also, please see "Transmitter Activated Anti-
Carjacking" in the Programmable Features section for an explanation of this related feature.
To access Features Programming Mode and change any of the Programmable Features:
Step #1: Turn "off" the ignition.
Step #2: Within 7 seconds of turning "off" the ignition, press the Valet Switch 5 times.
Step #3: You have just entered into the Feature Programming Mode. To confirm this, the
siren will respond with a siren burst. For the next 10 seconds the system is ready
for you to select what feature you wish to access and turn on or off. The Feature
Programming Mode will deactivate if a selection is not made within 10 seconds.
Step #4: Within 10 seconds of entering the Feature Programming Mode, press the Valet
Switch the number of times that equal the feature number you wish to access. After
pressing the Valet Switch multiple times the siren will chirp the same number of
times to confirm what feature number you are now accessed to for programming.
Example: Press the Valet Switch 5 times and the siren will chirp 5 times.
Step #5: To turn on the feature press the large transmitter button. The siren will chirp once
to confirm that the feature is turned on. To turn off the feature, press the small
transmitter button. The siren will chirp twice to confirm the feature is turned off.
Remember, 10 seconds of no programming activity will result in the system
automatically exiting the Feature Programming Mode, which is indicated by two
siren bursts.
Page - 17
Page - 19
Programmable Features
The FREEDOM-200+P security system has 16 Programmable Features, that may be
easily changed through the Features Programming Mode. The Programmable Features, and
their factory-set default setting, are:
Feature #1:
Current Sensing: Default ON.
Feature #2:
3.5 Minute or 3 Second Current Sensing Delay: Default 3.5 minutes.
Feature #3:
Last Door Arming: Default OFF.
Feature #4:
Doors Lock With Last Door Arming: Default OFF.
Feature #5:
Automatic Rearming: Default OFF.
Feature #6:
Doors Lock with Automatic Rearming: Default OFF.
Feature #7:
Steady Siren or Pulsed Horn Output: Default Steady Siren.
Feature #8:
Horn Confirmation Loud or Soft: Default Soft.
Feature #9:
Doors Lock and Unlock With Ignition On and Off: Default ON.
Feature #10: Open Door Bypass For Previous Feature: Default ON.
Feature #11: 30 or 60 Second Activation Duration: Default 60 Seconds.
Feature #12: Double Unlock Pulse: Default OFF.
Feature #13: Open Door Arming Alert: Default OFF.
Feature #14: Remote Trunk Release Also Disarms Alarm: Default ON.
Feature #15: Transmitter Activated Anti-Carjacking: Default OFF.
Feature #16: Door Activated Anti-Carjacking: Default OFF.
The 16 Programmable Features explained:
1) Current Sensing: (Default ON) When this Feature is on, the system will activate
while armed if a current draw is detected in the vehicle's electrical system. As an example,
if a vehicle door is opened the system will detect the current draw made by the dome light
illuminating. When programming, at Step #5 in Features Programming Mode press the
transmitter's large button to turn this Feature on or press the small button to turn this Feature
off.
2) 3.5 Minute/3 Second Current Sensing Delay: (Default 3.5 Minute) This Feature
sets one of two time delays before the Current Sensing Feature will operate after arming the
security system. Vehicles having delay dome lights or electric cooling fans may require the
longer setting. When programming, at Step #5 in Features Programming Mode press the
transmitter's large button to set this Feature for 3.5 minutes or press the small button to set
this Feature for 3 seconds.
3) Last Door Arming: (Default OFF) If this Feature is turned on, Last Door Arming
will operate. Last Door Arming starts after the ignition switch has been turned "off" and the
last open door is closed. The moment the last door closes the system will chirp the siren,
flash the parking lights once, and begin a countdown (during this countdown the LED Status
Light will be flashing fast). Thirty seconds after the last door was closed, the siren will chirp
again, the parking lights flash once, and the LED will begin to flash slow, confirming that
the security system is fully armed. If a point of entry is reopened before the 30 seconds
Page - 18
Page - 20