DANLERS WAPIRX Kurulum Notları

Anahtar DANLERS WAPIRX için çevrimiçi göz atın veya pdf Kurulum Notları indirin. DANLERS WAPIRX 2 sayfaları. 2-wire wall mounted pir occupancy switch

Sayfayı Yazdır

Lux and Time set-up

For convenience, ensure that the TIME is set to the minimum and the

button in when setting up the LUX level. Afterwards set the TIME and

SENS to values suitable for the application.

The LUX is best set up when the local ambient light is close to the

minimum desired light level. With the LUX set fully clockwise wait for the

WAPIR to switch off. Rotate the LUX adjuster slowly anticlockwise (- to

+), whilst waving your hand approximately 1m in front of the WAPIR,

until the load switches on.

Fault finding

The load will not switch on:

• The override switch is in the 'out' position.

The load stays permanently on or off, possibly after a few weeks.

• The load is less than 40W RESISTIVE per switch and the

rechargeable battery has not been able to recharge.

Add one power factor correction capacitor, at a light fitting, for

each WAPIR in the circuit. Order code: CAPLOAD.

Replace battery with a similar, recharged, rechargeable battery.

Alternatively, put the button out (override off) and with the

product loose on the wall, tap it with a screwdriver handle, the

lamps will switch off and the battery will charge.

Precautions and Warranty

This product conforms to BS EN 60669-2-1.

Please ensure the most recent edition of the appropriate local wiring regulations are observed

and suitable protection is provided e.g. 6 amps over current, 1kV over voltage. Please ensure

that this device is disconnected from the supply if an insulation test is made.

This product is covered by a warranty which extends to 5 years from the date of manufacture.

Also available from DANLERS

• PIR occupancy switches • Daylight linked dimmers • Manual high frequency dimmers

• Photocells • Radio remote controls • Time lag switches • Outdoor security switches

• Dimmers • Heating, ventilation and air-conditioning controls • Bespoke / O.E.M. products

Please call for more information or a free catalogue.

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388

E-mail: [email protected]

Web: www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

01/05/12

2-wire wall mounted PIR occupancy switch

WAPIR

DANLERS 2-wire wall mounted passive infra-red occupancy switch

(WAPIR) does not require a neutral connection and can be used as a

simple replacement for an existing one-way wall switch.

The WAPIR incorporates a passive infra-red quad sensor to detect movement

of a warm body within the detection zone (diagram A) and a photocell to

monitor the ambient light level.

Upon detecting movement, if the ambient light is dark enough, the WAPIR

switch will turn the load on. The ambient threshold can be set by the user

to between approximately 100 lux and infinite lux (photocell inactive) via

the LUX adjuster (diagram B).

If no more movement is detected within a pre-selected time, then the

WAPIR switch will turn the load off. This time lag can be set via the TIME

adjuster to 10 seconds, 20s, 40s, 1 minute 15 seconds, 2m30s, 5m, 10m,

20m or 40 minutes (diagram B).

The WAPIR also incorporates a sensitivity adjuster. Turn fully clockwise

for maximum range and sensitivity of the person detector.

The WAPIR has a manual switch on the front plate to select between

'override off' (button out) or 'automatic mode' (button in). The button

on the WAPIRX is accessed through a small hole in the front of the unit

and functions in the same way.

Several WAPIR units can be wired in parallel, using re-functioned 2-way

lighting wiring, to allow multiple PIR detection (diagram C).

Loading limits

The WAPIR should only be connected to a 230V 50Hz AC supply.

DANLERS WAPIR units can switch up to 6amps (1500W) of:

• Fluorescent lamps, either high frequency of switch start

• Incandescent or mains halogen lamps

• Electronic or wire wound transformers.

They can also switch up to:

• 2 amps (500W) of compact fluorescent or LED lamps (typically 50 lamps)

• 1 amp (250W) of Fans.

Larger loads can be switched via a contactor (see over).

INS949 WAPIR

Installation notes

WAPIRX

(recommended with integral safety fuse)