DANLERS CZ HB SP 10VDC Kurulum Notları - Sayfa 2

Aydınlatma Ekipmanları DANLERS CZ HB SP 10VDC için çevrimiçi göz atın veya pdf Kurulum Notları indirin. DANLERS CZ HB SP 10VDC 2 sayfaları. Controlzapp high bay controls for 1-10vdc ballasts

Sayfayı Yazdır

Installation procedure

1. Please read these notes carefully before commencing work. In case of doubt

please consult a qualified electrician. Ensure wires and cables are securely held

within the connection terminals.

IMPORTANT: The CZ HB (xx) 10VDC Control Unit clock battery must be

engaged (ON) prior to installation by switching the RED dip switch (see

diagram D) to the DOWN position.

2. POSITIONING: The CZ HB (xx) 10VDC switch should be installed to achieve

correct coverage of the area, see diagram B. If the photocell override facility

(enabled via ControlZAPP app) is required, the switch must be located above an

area where daylight can give greater illumination than the artificial light. Avoid

locating this product where it is exposed to drafty conditions (exposed lobbies,

open ceiling voids or near fans) or near heat sources.

3. Disconnect the ControlZAPP device from the circuit before performing insulation

testing of the wiring circuit.

4. Do not connect on a circuit with large inductive loads, as induced spikes may

cause false triggering or damage the device.

5. CZ HB (xx) 10VDC must be connected to the ControlZAPP Power Supply (CZPS)

via the ControlZAPP communication cable (telejack)provided, for wiring see

diagrams C and D. NOTE: The use of non ControlZAPP connectors may damage

the CZ HB (xx) 10VDC or CZPS and will invalidate the warranty).

6. Knockout or drill the appropriate holes on the mounting plate for attaching

the plate to the ceiling or back box (if applicable). Feed telejack through the

appropriate (side or rear) entry hole. Screw the back mounting plate to the ceiling

or back box via the mounting holes. Push the telejack connector into the sensor

head terminal. Push the sensor head onto the mounting plate and align the side

clips with the slots on the sensor heads.

Settings and calibration

NOTE: ALL settings are adjusted by ControlZAPP App as specified in the

ControlZAPP App User Guide (downloadable from the DANLERS website)

including: MODE settings, SCHEDULER settings and photocell settings and

intelligent photocell calibration procedure.

MODE settings include: Detect Movement (enable or disable), Sensitivity, Short

Visit Mode (with timer), Turn ON automatically (Presence detection or Absence

detection), Turn OFF timeout (from10sec to 23hrs 59min 59sec), Respond to

Daylight (enabled or disabled) the calibration process must be run for the intelligent

photocell to work. Delay before ON or Delay before OFF timers, Scene Recall (ON

or OFF).

SCHEDULER settings include:

DAY TYPES (defining times for each of the different Modes to occur).

WEEKLY SCHEDULE (defining which Day Types are assigned to different days of

the week).

EXCEPTIONS (defining exceptions to the schedule such as holidays).

VIEW ON CALENDAR (overview of schedule).

A: Detection diagrams

NARROW

SPOT

DETECTION (ND)

DETECTION (SP)

Mounting height

up to 12m

up to 20m

Perspective view -

ceiling mounted

15m

Up to 5m

diameter

Up to 3m

B: Wiring diagram

CZ HB (XX) 10VDC

100 - 260VAC

50/60Hz

Optional

other load

C: Mounting plate fixing

Knock out mounting

For telejack entry from

holes or pre-drill

above - knock out

pilot holes.

central mounting hole

D: Connector diagram

IMPORTANT

Red dip switch (MUST be

switched towards centre of control)

to engage clock battery ON

Power Supply

Telejack connector

WIDE

DETECTION (WD)

Mounting height

up to 14m

Perspective view -

ceiling mounted

Up to 28m

diameter

control lines

ballast

For side entry -

Clip telejack into the device

then join device to mounting

knock out side

mounting hole

plate via mounting clips

Control Unit