Dansing Wings SCG37 Kullanım Kılavuzu - Sayfa 3

Oyuncak Dansing Wings SCG37 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Dansing Wings SCG37 8 sayfaları.

Sayfayı Yazdır

02-3

02-4

Epoxy glue

此时不要粘固

02-6

Do not glue at this point

将连接钢丝插入水平尾翼预切槽中，然后检查两个舵面是否平直。如果没有，可以将钢丝取

出并调整，直到舵面保持平整和笔直。

Insert the connecting steel wire into the pre-cut slot of the horizontal tail wing,then

check the 2pcs rudder surface are straight and flat or not.If not, you can draw out the

steel wire and adjust it until the rudder surface keep flat and straight.

02-7

上一步骤调整好后，取下钢丝穿入机身尾部，如上图。

After the adjustment in the previous step, remove the

steel wire and insert it into the tail of the fuselage as

shown in the above picture.

02-9

注意：安装升降舵时，舵角的预留孔放置到预留了连杆的一边，和连杆相对，

方便后续安装。

Note: When install the elevator,the reserved hole of the rudder horn is

placed on the side of the reserved connecting rod, opposite to the

connecting rod, so as to facilitate subsequent installation.

02-5

Epoxy glue

玻纤管

Fiberglass tube

Ø8x150mm

安装升降舵到尾翼上，纸合

02-8

页和U型钢丝同时插入舵的

预留槽，用快干胶粘固。

Install the elevator on the

tail wing, insert the paper

hinge and U-shaped steel

wire into the reserved

slot on the rudder

surface at the same time,

纸合页

and fix it with quick

drying adhesive.

paper hinges

02-10

Epoxy glue

安装转向舵到垂直尾翼，通过针式铰链连接，并保持舵面可以自

由摆动。

Install the steering rudder to the vertical tail, connect it

through the pin hinge, and keep the rudder surface free to

swing.

02-11

自攻螺丝

Self-tapping screw

M2x10mm

02-12

安装机翼

Assemble the Wing

下机翼

03-1

lower wing

纸合页

paper hinges

把副翼安装到机翼上，纸合页插入机翼和副翼的预留槽内，两者通过纸合页

连接。纸合页装好后用CA胶粘固。同时保持副翼可以自由摆动。

Install the aileron on the wing, insert the paper hinge into the

reserved slot of the wing and aileron, and the two are connected

through the paper hinge. The paper hinge is fixed with CA glue after

being installed. At the same time, the aileron can swing freely.

03-3

取下机翼上舵机盖板，如图安装舵机。舵机用小木块固定住，木块用CA胶粘在盖

板上。

Remove the servo cover on the wing and install the servo as shown in the

figure. The servo is fixed with small wooden blocks, which are stuck on the

cover plate with CA glue.

参考尾轮罩位置，在上图螺丝位置钻孔，孔内点入少量CA胶，待胶水干后用

自攻螺丝固定住装饰罩。

Refer to the position of the tail wheel cover, drill holes at the screw

positions in the picture above, point a small amount of CA glue into

the holes,

and fix the decorative cover with self-tapping screws after the glue

dries.

尾轮杆

tail wheel rod

调整此处达到合适的伸出长度

Adjust this point to reach the

appropriate extension length

02-13

锁定

Lock

尾轮杆

wheel rod

03-2

03-4

舵机盖板装回机翼，用自攻螺丝锁定。舵机线穿入机翼内，从机翼

侧边导出。

Install the servo cover back into the wing and lock it with self

tapping screws. Insert the servo wire into the wing and exits

from the side of the wing.