Audioplex VCRunner OptiMatch Kurulum Kılavuzu

Transformatör Audioplex VCRunner OptiMatch için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Audioplex VCRunner OptiMatch 2 sayfaları.

Sayfayı Yazdır
Attenuator type:
Switch:
Connector:
Power rating:
Core Saturation:
Transformers:
Mounting:
PurePath :
TM
OPTIMATCH :
TM
Installation must be made by qualified service personnel, and must meet all local codes.
1.
Make connections by stripping the wire insulation back about 3/16". Twist any loose strands tightly.
2.
Insert the wires from the amplifier into the INPUT openings of the connector, hot to hot and ground to
ground, then tighten the screws. Check for any loose strands that might cause a short circuit. Make
sure the metal part of the screw connector engages the bare wire, NOT the insulation.
3.
Similarly, connect speaker wires to the control OUTPUT openings and tighten screws.
4.
If using the impedance matching feature of the OPTIMATCH(tm) control, set the index following the chart
below. To set, remove knob and loosen nut to reposition index. Make sure index is not between detent
positions and tighten.
5.
Install the control in its operating location. (SUGGESTION: Leave control 3 or 4 positions CCW from
maximum before firing up the system for the first time to avoid "blasting" the speakers, while still having
enough sound to observe operation.
OPTIMATCH(tm) is a new concept in self-impedance matching controls. It can be used either as a full range
volume control, or as an impedance matching volume control that can be adjusted to meet the requirements of your
installation. One simple adjustment can be made when the control is connected, and can be changed to accommodate
additions to the installation at any time. It is easily retrofitted to almost any existing system.
IMPEDANCE MULTIPLES
X32
(STEP 7)
X64
(STEP 6)
X128
(STEP 5)
Not actual
X256
peg position
(STEP 4)
X512
(STEP 3)
X1024
(STEP 2)
OFF
(STEP 1)
We do not recommend wiring more than 12 Optimatch(tm) controls in parallel. In these instances more impedance protection
should be inserted before the volume controls. The OC-12 or MS-12 is a good choice in this case.
INSTALLATION MANUAL
TECHNOLOGY
VCRunner PurePath or OptiMatch
TM

SPECIFICATIONS

Tapped auto transformer.
12 position rotary, make-before-break contacts, low torque specifications for
smooth feel.
Screw-tight type; 1-stereo input, 1-stereo buss, & 2-stereo outputs
UL Listed @ 72 Watts RMS continuous, 35 Hz- 20 KHz, 216 Watts audio.
Studies reveal that transformer core saturation @ 35 Hz is 72 Watts.
Tri-filar wound for flat response and minimum phase shift, grain-oriented,
-34 dB in 12 steps, 8 steps @ -3 dB each, 1 step @ 4 dB, 1 step @ -6 dB,
last step OFF.
Fits most standard single gang junction boxes.
This is a non-impedance matching version. When used must have impedance
matching else where.
With this option it will match impedance for almost any situation. Mechanical index
permits presetting load impedance multiplication by X2, X4, X8, X16,which can be
changed at any time.
INSTALLATION
X16
(STEP 8)
X8
(STEP 9)
DEFAULT
FACTORY
X4
(STEP 10)
SETTING
X2
(STEP 11)
FULL
ON
(STEP 12)
#4 Ohm
#8 Ohm
Load
Speakers
Speakers
(Ohms)
Per Channel
Per Channel
2
4.0000
3
2.6667
4
2
2.0000
5
1.6000
6
3
1.3333
7
1.1429
4
8
1.0000
9
0.8889
10
5
0.8000
11
0.7273
6
12
0.6667
Listed
Audio Equipment
P11 CCC 2
94V 0
No. of Available
Tap Setting
Steps for
For Matchit(tm)
Optimatch(tm) Controls
X2
11
X4
10
X4
10
X8
9
X8
9
X8
9
X8
9
X16
8
X16
8
X16
8
X16
8
2000 - 10/1/00